Monnit ALTA MNS2-4-PK-WS-PS User Manual Download Page 21

SAFETY RECOMMENDATIONS 

-

READ CAREFULLY

Be sure the use of this product is allowed in the country and in the environment required. 

The use of this product may be dangerous and has to be avoided in the following areas: 

Where it can interfere with other electronic devices in environments such 

as

hospitals,  airports,  aircraft,  etc. 

Where there is risk of explosion such 

as 

gasoline stations,  oil refineries,  etc. 

It is responsibility of the user to enforce the country regulation and the specific 

environmental regulation. 
Do not disassemble the product; any mark of tampering will compromise the warranty 

validity.  We recommend following the instructions of this user guide for correct setup and 

use of the product. 
Please handle the product with care, avoiding any dropping and contact with the internal 

circuit board 

as 

electrostatic discharges may damage the product. The 

same 

precautions 

should be taken if manually inserting a SIM card, checking carefully the instruction for its 

use. Do not insert or remove the SIM when the product is in power saving mode. 
Every device has to be equipped with a proper antenna with specific characteristics. The 

antenna has to be installed with care in order to avoid any interference with other electronic 

devices and has to guarantee a minimum distance from the body (23 cm). In 

case 

this 

requirement cannot be satisfied, the system integrator has to 

assess 

the final product 

against the Suspicious Activity Reports (SAR) regulations. 

The European Community provides 

some 

Directives for the electronic equipment 

introduced on the market. All the relevant information's is available on the European 

Community website: http://ec.europa.eu/enterprise/sectors/rtteldocuments/ 
The text of the Directive 99/05 regarding telecommunication equipment is available,  while 

the applicable Directives (Low Voltage and EMC) are available at: 

http://ec.europa.eu/enterprise/sectors/electrical 

Additional Information and Support 

For additional information or more detailed instructions on how to use your Monnit Sensors 

or iMonnit,  please visit us on the 

Monnit, iMonnit and all other trademarks are property of Monnit, Corp. © 2021  Monnit Corp. All Rights Reserved. 

WS-PS-AUG (10/21) 

Summary of Contents for ALTA MNS2-4-PK-WS-PS























Reviews: