Monitor Technologies SiloPatrol Installation & Operation Manual Download Page 1

S

S

i

i

l

l

o

o

P

P

a

a

t

t

r

r

o

o

l

l

®

Wireless Communication Interface

B U L L E T I N

3

34

44

4H

H

Standard Antenna

I N S T A L L A T I O N   &   O P E R A T I O N

®

Thank you for purchasing a quality product manufactured by Monitor
Technologies LLC.  We realize that you do have a choice of vendors
when buying instrumentation and we sincerely appreciate you business!

This manual contains the information necessary to ensure a safe and
successful installation.  Please read and comply with the section on
page 10 of this manual pertaining to SAFETY.  Doing so will ensure prop-
er operation of the equipment and the safety of all personnel.

Before discarding shipping container or the internal packing materials,
please inspect the packaging thoroughly and verify that all parts are
accounted for.   This product is shipped with the antenna, and mounting
plate (with its fasteners) detached from the Wireless Communication
Interface (radio module).  

In the event that information contained herein does not completely sat-
isfy your requirements or answer your questions, you may contact
Technical Support on our website www.monitortech.com, by telephone
at 800-766-6486  (630-365-9403) or by fax at 630-365-5646.  If your

Silo

Patrol

Wireless Communications Interface ever requires service

either in or out of warranty, please contact us and obtain an RMA num-
ber prior to shipping the unit to us.

 

 

 

  

 

 

 

 

 

 

Summary of Contents for SiloPatrol











Reviews: