USE OF THE BATTERY OPERATED JEEP
Notice:
1. When you change the direction of movement, first make sure that the jeep does not move. Otherwise, if you
change suddenly the direction of movement without stopping the jeep, you may cause damage of the gears and
motor.
2. If you are using the remote control, please, follow the guidelines inn this instruction manual.
FIGURE А6
The dashboard consists of the following:
1 – Forward/backward switch
2 – Battery indicator
3 – Pedal
4 – Power button
5 – MP3 interface
6 – Volume button
•
Start:
Switch the power button to open position and the jeep must be in active mode.
•
Forward:
1. Press the Forward-Backward switch to Forward position.
2. Press the pedal and the jeep will start moving forwards.
•
Backward:
1. Press the “forward-backward” switch to „backward”. position.
2. Press the pedal and the jeep will start moving backwards.
•
Stop:
The jeep will automatically stop after you release the gas pedal.
•
MP3:
Turn the power button on and connect one end of the MP3 cable to the output of the dashboard, connect
the other to the MP3 player.
Do not put the MP3 player close to the ears and do not listen to loud music, because this may lead to
impairment of the hearing
REMOTE CONTROL USE
WARNING!
The remote control can be used by an adult only!
Placing the batteries inside the remote control:
The remote control works with batteries, which are not included in the
product. Remove the screw from cover of the battery compartment, then remove the cover and place the batteries. Observe
the correct polarity, indicated at the bottom of the compartment, as well as and the correct size. Place the lid back and fasten
it with the screw.
Warning!
The placing and further replacement of the batteries must be performed by an adult!
How to operate with the remote control – See FIGURE A7
А.
Forward
D.
Speed selection
G.
Turning right
B.
Stop
E.
Frequency button
H.
Turning left
C.
Backward
F.
Indicating LED lights for the speed – low, middle, high
1. Place batteries in the battery compartment of the remote control.
2. Press the frequency button continuously for 2-4 seconds. The indicating lights for low speed will start flashing.
3. turn on the power button of the jeep and when the indicating lights for low speed will start shining continuously in red, the
connection is successful . Now you can use the remote control.
4. if the connection is not successful, then the indicating light will be flashing, it will not shine continuously. In this case turn
off the jeep from the power button and take out the batteries from the remote control. Repeat the steps from 1 to 3.
5. Press the forward/ backward button to position forward and the battery operated jeep will move forwards. Press the
backward button and the jeep will start moving backwards.
6. The speed selection button allows you to move at low, normal and high speed. It will not work at reverse.
7. Press the button for turning left / right at position left and the jeep will turn left. Press the button right and the jeep will turn
right.
8. Press the stop button and the jeep will stop. Press it again so the jeep starts again.
9. If you do not use the remote control for about 10 seconds, then it will turn off automatically.
Important:
• Do not use this product in areas of high voltage areas, gas stations, hospitals and transformers.
• Keep a distance at maximum 10 meters between the RC and the jeep. If at the place of using the jeep, there are other
battery driven toys, you should not use the function of the RC.
• Do not push the button for turning left/ right for more than 10 seconds as this may lead to overheating and damage of the
motor.
•
WARNING:
If the batteries do not have enough charge, you will be able to control via the remote control only the forward
and backward motion of the jeep. Please, immediately replace the old batteries with new ones.
•
WARNING:
When the jeep is driven through the remote control, the pedal must not be pressed, because this will influence
the normal movement of the jeep.
13
Summary of Contents for Mercedes-Benz GL 63 AMG (X166) LS-628
Page 2: ...1 ...
