GB
I. WARNING
•
Warning!
It contains small parts. Suffocation hazard.
•
It must be careful while you unpack and assemble the toy. Keep the children away from you, when you do these actions.
•
Suffocation hazard! Keep the plastic packages away from children..
•
Do not allow to the child to take off the stickers if there are any over the product and to swallow them.
•
The materials, which the product is made of, are suitable and safe for children’s health.
II. WARNINGS AND REFERENCES FOR SAFETY USAGE
1.Warning!
To be used under the direct supervision of an adult.
2. This ride-on car is suitable for children aged 3-5 years, weighing up to 20 kg. The product cannot support extra weight!
3. The toy is intended for use by one child only.
4. The assembly and installation should be performed by an adult. The product contains small or sharp and protruding parts.
5.Warning!
During assembly children should not be present. Choking hazard! Small parts.
6.The batteries must be handled by an adult only.
7.Not to be used in traffic.
8.Not to be used on steep slopes or near stairs, near swimming pools or other water bodies. Use the product only on even grounds and
safe areas.
9.Do not allow another child to push the ride-on car while your child uses it.
10.Check regularly the condition of each part. In case of damage there is a risk of injuring your child.
11.Check regularly whether the nut and bolt on the steering wheel are fixed tightly and do not represent any danger.
12.If the product is not assembled properly this may lead to danger.
13.Do not allow the child to use the ride – on car barefoot.
14.The toy complies with Standard EN71 and meets the essential requirements for “General safety of the product”.
15.Risk of suffocation. Remove all plastic packing immediately after unpacking the product.
III. HANDLING OF THE BATTERY
1. The battery should be handled by an adult only. Do not allow the children to play with the batteries.
2.Always remove the discharged batteries and do not throw them away with the household waste, use the places designated for that
purpose. They are recyclable.
3. Use АА batteries only.
4. Alkaline batteries are recommended.
5. Always remove the batteries, if you will not use the product for a long period of time.
6. When you replace the batteries always replace them with new ones, always replace all batteries. Children should not be present
while you are replacing the batteries.
7. Do not mix old batteries with new ones.
8. Do not mix alkaline, standard (Carbon - Zinc), or rechargeable (Nickel – Cadmium) batteries.
9. Do not throw the batteries in fire, because they may blow up or leak.
IV. CLEANING AND MAINTENANCE OF THE PRODUCT
CLEANING:
1.Regularly clean the product.
2. Do not use corrosive power cleaning agents or cleaning agents on alcoholic base and those, containing abrasive particles.
3. Clean with soft wet cloth. Always dry with dry soft cloth after this.
MAINTENANCE AND STORAGING:
1. Regularly check the product for broken or damaged parts. If you find any, do not use the product, until you remove the damage.
2. In case of damage, please contact the trade agent, which you bought the product from or the importer.
3. Do not repair by yourself! Do not make any modifications or changes over the product! This can threaten your child’s health.
4. Regularly check whether the main parts of the car are in good condition (steering wheel, main corpse and wheels).
5.Keep the product from prolong exposure on sunlight, as also from heating sources.
6. Storage on dry and windy place, away from direct heating sources – open fires, cooking ovens and heating appliances.
V. PARTS OF THE PRODUCT AND ASSEMBLING SCHEME– LOOK PAGE 1
On the table are marked the following parts: 1.Car body; 2.Steering wheel; 3. Front fork; 4.Safety board; 5.Rear wheel holder;
6.Backrest; 7.Wheels; 8.Axle; 9.Parent control handle; 10.Canopy; 11.Foot rests; 12. and 13.Bags with parts assisting the assembly.
VI.INSTRUCTIONS FOR ASSEMBLING OF THE PRODUCT
Carefully read the instructions before starting to assemble the product. Follow exactly the separate steps of assembling and check after
each action whether you have fixed the separate parts well.
The schemes in this manual are only illustrative.
The manufacturer keeps
his right to change the way of assembling the product, without to notifying the customer in advance.
1.Step 1 – See figure 1 – Attaching the front wheels:
Slide the front axle through the openings of the front fork. Attach one wheel to
each side of the axle. Then put on each side bushing and cotter pin in order to fix the wheels. Attach the decorative plastic rims to the
wheels.
2.Step 2 – See figure 2 –Attaching the rear wheels, steering wheel and backrest:
-
Rear wheels:
Attach the rear wheels holder to the car body. Fix it with 4 screws. Slide the rear axle through the openings in the
holder. On each side of the axle place one wheel and then one gasket. Fix the wheels using the cotter pin and finish with placing the
decorative rims.
7
