PARTS LIST
Before you start to assemble the battery-operated car, take the parts out of the packaging and check whether all parts
indicated in the list below are present. Keep the packaging until you have completely finished the assembly.
See the table on page 1 and Figure PD
: 1. Car body
– 1 pc; 2. Front decorative windshield – 1 pc; 3. Seat (fixing screw
attached to it)
– 1 pc; 4. Rear gearbox – 2 pcs; 5. Wheels – 4 pcs; 6. Rear spoiler – 1 pc; 7. Steering wheel – 1 pc; 8.
Rearview mirrors
– 1 set; 9. M10 Washer attached to the front and rear axles – 6 pcs; 10. Remote control – 1 pc; 11. M8
Nuts attached to the front and rear axles
– 4 pcs; 12. M5 x 35 bolt and M5 Nut attached to the steering wheel – 1 set; 13.
Wheel caps
– 4 pcs; 14. Charger – 1 pc; 15. M4x12 screws – 6 pcs; 16. Covers attached to the wheels – 4 pcs; 17. User
manual
– 1 pc; 18. Spanner– 2 pcs; 19. MP3 cable– 1 pc; 20. Auxiliary wheels – 2 pcs;
ASSEMBLY STEPS
On Figure T are shown the tools that you will need during the assembly:
S
– screwdriver (not provided with the
product); P
– pliers (not provided with the product); H – hammer (not provided with the product); W – wrench (not provided
with the product);
1.Auxiliary and rear
wheels’ installation – See Figures 1a and 1b:
Turn
car’s body upside down. Remove the M4x12
nuts from the rear car body. Attach the auxiliary wheels to the corresponding holders on the rear car body. Fix them using
the M4x12 screws. Then attach the rear gearboxes to the rear axles. Attach to the left and right side of the rear axle: rear
wheel
→ washer → M8 nut. The cogwheels of the wheels must fit tightly to the cogwheels of the gearboxes. Using a
spanner tighten both of the nuts on each side of the rear axle. Then attach the caps to the wheels. Push them carefully to fix
them. You will hear a click.
2.Front
wheels’ installation – See Figure 2:
Remove two nuts and 4 washers from the front axle. Attach to the left and
right side of the front axle: washer
→ front wheel → washer → M8 nut. Use a spanner to tighten the nuts on both sides of
the front axle. Then attach the covers to the wheels. Push them carefully to fix them. You will hear a click.
3.Connecting the battery
– See Figure 3:
Turn the car body so that it stands on its wheels. Connect the red cable to the
red terminal of the battery. Follow the correct polarity.
Never
connect black cable to red terminal or vice versa. This may
lead to short circuit. Turn on the power of the car to check if the connection was successful.
4.Attaching the seat and rear spoiler
– See Figure 4:
Remove the screws M4x12mm from the designated part of the car
body to which the rear spoiler is attached. Attach the spoiler to its designated place. Fix using the M4x12mm screws and
screwdriver. Place the seat at the rear part of the car. The plastic pins of the rear part of the seat must be fixed into the
corresponding openings in the
car’s body. Fix the front part of the seat with 2 screws M4x12mm.
5.Attaching the front windshield
– See Figure 5:
Attach the windshield to the front part of the
car’s body. Insert its plastic
pins into the corresponding openings of the body. Press carefully down to fix it.
Warning!
Do not press too hard as you may
break some of the parts.
6.Attaching the steering wheel
– See Figure 6:
Remove the fixing M5x35 bolt and nut from the steering wheel. Connect
the steering
wheel’s cable to the car’s cable. Then insert the cables into the opening. Place the steering wheel on the tip of
the steering rod.
Warning!
Be careful not to damage the cables. Align the openings of the steering rod and steering wheel.
Slide the fixing bolt M5x35 and fix it using the nut and screwdriver.
7.Fix the rearview mirrors
– See Figure 7:
Before attaching the mirrors, make sure to differ the right from the left mirror.
Place the rearview mirrors in the corresponding openings on the doors. Press carefully until they are fixed.
Notice:
1. When you change the direction of movement, first make sure that the car does not move. Otherwise, if you change
suddenly the direction of movement without stopping the car, you may cause damage of the gears and motor.
See Figure U:
1.MP
–
Music player.
2.P & F/R
– Buttons for turning the car on or off and Front/ Rear moving.
3.FP
–
Foot pedal.
Moving Forward/ Reverse:
•
Moving Forward:
Put the Forward
▲ / Reverse ▼ switch in position Forward ▲ and press the pedal in order to move the
car forward.
•
Moving Backward:
Put the Forward
▲ / Reverse ▼ switch in position Reverse ▼ and press the pedal to move the car
backwards.
•
Stop:
Lift your leg from the pedal in order to stop the car from moving.
See Figure MP:
1.USB jack
–
to connect audio device for music playing.
2.TF slot
–
to insert SD card.
3.Previous song/ volume down:
Press once for the previous song or press and hold for volume down.
4.Pause/ Play:
Press once for pausing the music. Press one more time the button for playing the music again.
5.Next song/ volume up:
Press once for the next song or press and hold for volume up.
6.Mode button:
Press for playing music from the MP3 player. Press one more time the button to change to playing from the
audio devise connected to the USB or for music playing from the TF card.
7.Battery display
–
shows the left charge in the battery.
USE OF THE BATTERY-OPERATED CAR
18
Summary of Contents for AMG GT_R
Page 2: ...ДИАГРАМА НА ЧАСТИТЕ PARTS DIAGRAM 1 ...
Page 3: ...2 СТЪПКИ НА СГЛОБЯВАНЕ УПОТРЕБА И ЗАРЕЖДАНЕ ASSEMBLY STEPS USE AND CHARGING ...
Page 4: ...3 ...
Page 5: ...4 ...
