6 Calling the Camera via a Computer
As described in the preceding chapter, the user interface
of the camera can be called via the list in the search pro-
gram or by entering its IP address in the address line of the
program Windows Internet Explorer (IE). A maximum of 10
accesses to the camera is possible at the same time.
The computer used should meet the following minimum
requirements:
Processor, memory: . . . . . Intel Dual Core/ 2.53 GHz,
1024 MB RAM
Operating system: . . . . . . . Windows 2000, Windows XP,
Windows 7
Web browser: . . . . . . . . . . Windows Internet Explorer,
version 6 or higher
Graphics card: . . . . . . . . . . 128 MB memory,
32-bit colour resolution
Windows is a registered trademark of Microsoft Corporation in the USA and other
countries.
When calling the camera, first the log-in screen appears in
which the user name and the password have to be entered
(preset for both inputs: admin). Individual log-in data can
later be defined in the camera settings. At least the pass-
word should be changed against unauthorized access.
For the first connection set-up via the IE, the IE downloads
the required extensions (ActiveX control elements) from
the camera and installs them on the computer. If neces-
sary, the security settings of the IE must be eased before
installation so that this procedure is admitted.
When the connection to the camera is made, the current
camera image shown in fig. 3 is displayed, with the follow-
ing operating possibilities:
display size
option streaming 1 or 2 (to be configured)
option for the audio transmission to the camera
number of the current accesses to the camera
relay: for manual triggering the switching output
button to show a bar for adjusting the focus (the bar will
automatically disappear after 3 min.)
button to call the settings (Setup)
snapshot function to memorize a snapshot as an image
(with pre-view window)
Click the camera image with the right mouse button to
insert the following menu:
Snapshot – saving of a snapshot as an image
Record Start/ Stop – start / stop of a video recording on
the PC
Mute – muting of the camera sound
Full Screen – full-screen view (double-click to go back)
Zoom – section enlargement
FrameBuffmSec – buffer [ms]
To configure the camera, click the symbol next to
. The
settings are displayed (
fig. 4). Here, the language for
the complete user interface can be changed as well (
).
Select the desired category for the settings via the defini-
tions at the left edge (
).
To return to the start view (camera image), click the
symbol next to
.
7 Reset of the Camera
The camera can be reset to its factory settings. Then all
the changes the user may have made to the camera set-
tings are lost.
1) Disconnect the camera from the power supply.
2) Connect the terminal “Default” of the terminal block (6)
to the terminal GND and re-establish the power supply.
3) After the starting procedure of the camera (approx.
30 s), disconnect the connection.
The camera is now reset to the static IP address
192.168.1.200, the user name and the password for the
log-in is: admin
8 Adjusting Focal Length and Focus
Turn the screws at the lower side to adjust the focal length
[zoom (11)] and the sharpness [focus (12)].
9 Specifications
Image sensor: . . . . . . . . . . CMOS, 8.5 mm (
1
⁄
3
″)
Lens: . . . . . . . . . . . . . . . . . 1 : 1.8 / 3 – 9 mm
Minimum illumination: . . . . 0.1 lx (colour), 0.05 lx (b/ w)
Resolution: . . . . . . . . . . . . 20 images / sec max.
at 2048 × 1536 pixels
30 images / sec max.
at 1920 × 1080 pixels
Protocols: . . . . . . . . . . . . . TCP/ IP, DHCP, PPPoE, FTP,
SMTP, SNMP, NTP,
QoS/DSCP, DDNS, UPnP,
RTSP, HTTP, HTTPS, UDP,
3GPP, Bonjour, Samba,
IEEE 802.1X, Access list filter
Compression procedure: . . MPEG-4 H.264, MJPEG
Video streaming: . . . . . . . . 3-fold
Network: . . . . . . . . . . . . . . Ethernet 10 / 100 Mbit / s
or WLAN 802.11 b / g / n
Microphone input: . . . . . . . 3.5 mm jack
Audio output: . . . . . . . . . . . 3.5 mm jack, mono,
line level
Video output: . . . . . . . . . . . 1 Vpp / 75 Ω, BNC
Switching output: . . . . . . . . 5 V
/ 50 mA max.
Ambient temperature: . . . . -10 °C to +45 °C
Protective class: . . . . . . . . IP 66
Power supply: . . . . . . . . . . 12 V
, 1 A via
supplied PSU
Dimensions: . . . . . . . . . . .
∅
86 mm × 235 mm
Weight: . . . . . . . . . . . . . . . 500 g
Subject to technical modifications.
VNC -3040W
Order No. 18.3750
®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
A-1558.99.01.04.2014
®
