Monacor ENF-90 Operating Instructions Download Page 1

ELECTRONICS FOR SPECIALISTS    ELECTRONICS FOR SPECIALISTS    ELECTRONICS FOR SPECIALISTS    ELECTRONICS FOR SPECIALISTS

ENF-90

Bestell-Nr. • Order No. 06.4360

MONACOR INTERNATIONAL GmbH & Co. KG  •  Zum Falsch 36  •  28307 Bremen  •  Germany 

Copyright 

©

 by MONACOR INTERNATIONAL.  All rights reserved. 

A-0032.99.06.07.2019

12 V Noise Filter

These operating instructions are intended for experts 
with knowledge in the electrical system of the car. 
Please read the instructions carefully prior to installa-
tion and keep them for later reference.

1  Applications

The filter is specially designed to eliminate noise from 
the 12 V supply voltage for car radios or car HiFi power  
amplifiers.

2  Important Notes for Installation

This unit corresponds to all relevant directives of the EU 
and is therefore marked with

  .

• 

Install the filter rigidly and expertly at a mechanically 
stable place in the car so that it will not work loose and 
become a dangerous projectile.

• 

Do not exceed the continuous current load of 10 A max. 
or a temporary peak current load of 30 A max.!

• 

Be very careful when connecting the filter. In case of 
short circuit, there may be dangerous high currents. 
Therefore, before connecting, always unscrew the nega-
tive terminal of the car battery.

• 

No guarantee claims for the filter and no liability for 
any resulting personal damage or material damage will 
be accepted if the filter is used for other purposes than 
originally intended, if it is not correctly installed or con-
nected.

If the filter is to be put out of operation defini-

tively, take it to a local recycling plant for a dis-

posal which is not harmful to the environment.

3  Connection

1) Disconnect the negative terminal of the car battery.
2) For optimum noise elimination, install the filter close to 

the car radio / the car HiFi power amplifier so that the 

connection cable between the filter and the car radio /

car HiFi power amplifier is as short as possible. Rigidly 

install the filter at a suitable place.

3) Provide the cables of the filter with cable end sleeves.
4) Insert the filter in the 12 V supply line between the car 

battery and the car radio /car HiFi power amplifier: 

 

– connect the red cable to the fuse 

 

– connect the yellow cable to the load 

 

– connect the black cable to the car chassis 

 

Secure the clamping screws for the connection cables.

5) Reconnect the negative terminal of the car battery.

Subject to technical modification.

POWER

GROUND BATTERY REMOTE

SPEAKER OUTPUT

R

F

+12 V

+12 V

ENF-90

Sicherung

Fuse

Batterie

Battery

Radio oder Endsstufe

Radio or power amplifier

Masse

Ground

gelb

yellow

rot

red

schwarz

black

12-V-Entstörfilter

Diese Anleitung richtet sich an Fachleute mit Kennt-

nissen in der Kfz-Elektrik. Bitte lesen Sie die Anleitung 

vor der Installation gründlich durch und heben Sie sie 

für ein späteres Nachlesen auf.

1  Einsatzmöglichkeiten

Das Filter ist speziell zum Herausfiltern von Störungen aus 

der 12-V-Versorgungsspannung für Autoradios bzw. für 

Car-Hi-Fi- Endstufen  konzipiert.

2  Wichtige Hinweise zur Montage

Das Gerät entspricht allen relevanten Richtlinien der EU 

und trägt deshalb das  -Zeichen.

• 

Das Filter muss fest und fachgerecht an einer mechanisch 

stabilen Stelle im Auto montiert werden, damit es sich 

nicht löst und zu einem gefährlichen Geschoss wird.

• 

Die Belastung von max. 10 A Dauerstrom oder kurzzeitig 

max. 30 A Spitzenstrom darf nicht überschritten werden!

• 

Beim Anschluss des Filters ist besondere Sorgfalt ge-

boten. Bei Kurzschlüssen können sehr gefährlich hohe 

Ströme fließen. Deshalb vor dem Anschluss die Minus- 

klemme der Autobatterie abschrauben.

• 

Bei missbräuchlicher Verwendung, unsachgemäßer Mon-

tage oder falschem Anschluss kann keine Garantie für 

das Filter und keine Haftung für daraus resultierende 

Sach- oder Personenschäden übernommen werden.

Soll das Filter endgültig aus dem Betrieb genom-

men werden, übergeben Sie es zur umweltge-

rechten Entsorgung einem örtlichen Recycling-

betrieb.

3  Anschluss

1) Die Minusklemme der Autobatterie abklemmen.
2) Für eine optimale Entstörung das Filter in der Nähe des 

Autoradios / der Car-Hi-Fi-Endstufe befestigen, damit das 

Verbindungskabel zwischen Filter und Autoradio /

 

Car-

Hi-Fi-Endstufe möglichst kurz ist. Das Filter an geeigne-

ter Stelle fest montieren.

3) Die Kabel des Filters mit Aderendhülsen versehen.
4) Das Filter in die 12-V-Versorgungsleitung zwischen Auto-

batterie und Autoradio / Car-Hi-Fi-Endstufe schalten: 

 

– rotes Kabel zur Sicherung 

 

– gelbes Kabel zum Verbraucher 

 

– schwarzes Kabel mit dem Autochassis verbinden. 

 

Die Klemmschrauben für die Anschlusskabel fest an-

ziehen.

5) Die Minusklemme der Batterie wieder anklemmen.

 

Änderungen vorbehalten.

Deutsch

English

Reviews: