background image

Tool Kit for CSP 6.3 Receptacle Terminal 

Doc No: ATS-6382558HM  Release Date: 08-13-12 

UNCONTROLLED COPY

 

Page 5 of 8 

Revision: A 

Revision Date: 08-13-12 

 

Maintenance 

 
It is recommended that each operator of the tool 
be made aware of, and responsible for, the 
following maintenance steps: 
 
1.

 

Remove dust, moisture and other 
contaminants with a clean brush, or soft, lint-
free cloth. 

2.

 

Do not use any abrasive materials that could 
damage the tool. 

3.

 

Make certain all pins; pivot points and 
bearing surfaces in the tool head are 
protected with a thin coat of high quality 
machine oil.  Do not oil excessively.  This tool was engineered for durability, but like any fine piece of 
equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping.  The use of 
light oil, such as 30 weight automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life 
and ensure a stable calibration.  See Figure 7A or 7B for lubrication points. 

4.

 

Store the tool in a clean and dry area when not in use. 

 

Miscrimps or Jams for Crimp Hand Tools Only 

(See Figure 10) 

 
Should this tool ever become stuck or jammed in a partially closed position, 

Do Not

 force the handles open or 

closed.

  The tool will open easily by rotating the small slotted screw marked with an arrow.  See Figure 10. 

 

Warranty 

This tool kit is for electrical terminal crimping purposes only.  This tool kit is made of the best quality materials.  All 
vital components are long life tested.  All tools are warranted to be free of manufacturing defects for a period of 30 
days.  Should such a defect occur, we will repair or exchange the tool kit free of charge.  This repair or exchange 
will not be applicable to altered, misused, or damaged tools.   
 

CAUTION

:  Molex crimp specifications are valid only when used with Molex terminals and tooling. 

 

CAUTIONS

 

1.

 

Manually powered hand tools are intended for low volume or field repair.  This tool is 

NOT

 intended for 

production use.  Repetitive use of this tool should be avoided. 

2.

 

Insulated rubber handles are not protection against electrical shock. 

3.

 

Wear eye protection at all times. 

4.

 

Use only the Molex terminals specified for crimping with this tool. 

 

CAUTION:

 Repetitive use of this tool should be avoided. 

 

Certification 

Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for 
customers to re-certify hand tools. 

LUBRICATION 

POINTS 

(BOTH SIDES) 

LIGHT OIL 

(EVERY MONTH 

 OR 

5,000 CRIMPS) 

Figure7A 

Figure 7B 

Summary of Contents for 63825-5800









Reviews: