background image

With the stereo Blue tooth receiver ClipR, you can control incoming 
and outgoing phone calls while you listen to music in stereo from 
your phone or from other devices. Such a device must support Blue tooth, 
for example, a computer or a por table music player. During a call, 
the music pauses automatically and starts playing again when the 
call ends.

Introduction

-2-

-3-

-1-

Overview

-4-

-5-

-6-

Charge Your Receiver

Highly recommend to charge your receiver 100% before usage. It 
takes approximately 2~3 hours to charge the receiver from 0% ~ 
100% for the first time.

1. Using computer: connect the micro USB cable to the receiver power 
connector and the standard USB port to computers USB port.

2. Using an electrical outlet: connect the micro USB cable to the 
receiver and the standard USB port to a DC 5V adapter.
3. Indicator status:
a. RED = charging
b. OFF = charge completed

1. Power ON:  Press and hold button 

 until the LED flashes in red 

and blue alternatively and a beep sound heard.

2. Power OFF: Press and hold button 

 until the LED flashes in blue 

and a beep sound

 

heard then release.

Turn ON / OFF the Receiver

1.Make sure your mobile phone is Blue tooth-enabled and the Blue 
tooth function is activated.
2.Ensure the receivers is turned off.
3.Receiver: Press and hold the MFB button   until the LED indicator 

flashes in red and blue alternatively.

4.Phone: Scan for 

Blue tooth

 devices, then select "MOCREO ClipR "in 

the available devices list.
5.Follow the pairing instructions that appear on your phone. If a 
password is required, enter "0000".
6.Go back to your mobile phones main menu. For some mobile 
phone, when they are re-started, the receiver will be connected with 
the mobile phone automatically.

1. Multi-functional button
    Power on/off, play / pause / receive a call, pairing mode

2. Track backward / Volume  
3. Micro USB jack
4. Track forward / Volume 
5. NFC detection area
6. LED indicator
7. Built-in microphone
8. 3.5mm AUX line out
9. Clip

Pair the Receiver with Your Phone

You can pair the receiver with your phone manually or using NFC. 
After successful pairing, the receiver connects automatically to the 
phone as soon as the receiver is turned on and within range.

To Manually Pair the Receiver with Your Phone

1.Make sure that the NFC function of you mobile phone is turned on 
and that the phone screen is active.
2.Turn on the receiver.
3.Place your phone over the receiver so that the NFC detection area 
of each device touches the other.

4.Follow the pairing instructions that appear on your phone. If a 
password is required, enter "0000".

Note: 
1.ClipR will automatically be turned off if no paired device is in range 
after 5 minutes. 
2.All the pairing information will be stored even after the power is off.

To Pair the Receiver with Your Mobile Phone via NFC

In standby mode, press button 

,   and   simultaneously until the 

①  ②

LED flashes in red and blue alternatively and a beep sound is heard, 
then release your hand.

Note:
Reset the receiver if it behaves unexpectedly. Resetting the receiver 
will remove all information about paired devices.

Reset the Receiver

Wearing Instructions

Although the clip is fixed and cannot be rotated, the device can be 
turned left or right depending on how it is clipped to your garment.
To get the best performance from a Blue tooth receiver when using it 
outdoors, it is recommended that you carr y your phone on the 
same side of your body as the receiver unit.

Call Handing

With a built-in microphone, ClipR enables you to receive and make 
calls while listening to music when paired with a smartphone.

1.Answer a call

The LED flashes in blue and the incoming call signal Ding-Dong will 
be heard. Press and release the button   once to answer a call.

2.End a call

Press and release the button   once during the call.

3.Decline a call

Press and hold the button   and release it after a long beep. The 

incoming call is declined.

4.To mute the microphone during a call

Press the button 

 and   simultaneously and release it until a Ding-

Dong sound is heard to mute the microphone during a call. And 
repeat above procedure to cancel the mute.

5.Last dialed number re-dial

Quick double press and release the button   to redial the last 

number dialed.

6.To transfer a call 

Press and hold the button   for 3 seconds during a call to transfer a 

call to mobile phone. And repeat above procedure to transfer the 
call from mobile phone to the receiver.

Listening to music

To listen to music

1. Open the media player in your phone.
2. Press button (1) to play the music on the receiver. To pause the music,
 press button (4) again.

To move between tracks

When you are listening to music, press button (2) and (4) for tracking 
control.

To control the volume 

Press and hold the button (2) and (4) to decrease and increase the 
volume when listening to music. 

Reviews: