Innovations – Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made
high-resolution video systems cost-efficient.
MOBOTIX AG • D-67722 Langmeil • Phone: +49 6302 9816-103 • Fax: +49 6302 9816-190 • [email protected]
EN
Quick Install
Indoor Camera p25
Security-Vision-Systems
www
.mobotix.com
2015 • Declaration of Confor
mity: www
.mobotix.com > Support > Media Library > Certi
ficates
Copyright © MOBOTIX AG 2015 • Made in Ger
many • T
echnical infor
mation subject to change without notice.
Removing the p25
1. Pull out the camera
Pull the camera from its position by gently pulling the camera downward
on one side, then the other side.
Take care to NOT let the spring clips
snap forward (risk of injury!).
2. Remove the cables
Remove the cables coming from the building (network cable, USB cable,
MxBus and signal input/output wires). Pull out the camera.
Installing the p25
Use the drilling template on the back for this purpose (red circle) or draw a circle with 105 mm/4.13 in diameter for the
cut-out. Cut out the hole for the camera, then guide the cables (network cable, USB cable, MxBus and signal input/
output wires) through the hole.
1. Install the p25
Press the spring clips back and insert the
p25 into the hole for the camera. The spring
clips will snap outwards, thus firmly holding
the camera in place.
Make sure that you only press back the
spring clips as shown in the image. Do not
press them back any further as the springs
may snap out of their fixtures otherwise.
2. Roughly align the p25
Turn the camera until it roughly points into
the intended direction; once it is running, you
will adjust the camera according to the live
image (see
«Initial Operation of the p25»).
Initial Operation of the p25
The initial operation starts with connecting the power supply (see section
«Network and Power Connec-
tion, Additional Cables» in the M25 Camera Manual). The first access follows the procedure described in
the same manual in the section «Initial Operation of the Camera». All other tasks require access to the
camera’s user interface in the browser. Enter the camera’s IP address into the address bar of the browser.
1. Set installed lens (only when self-mounting)
Open
Admin Menu > Hardware Configura-
tion > Lens Configuration
dialog and select
the installed lens. This step is required to select
the proper special functions of the installed lens
(e.g., for wide-angle lenses).
2. Adjust lens focus (if required)
This step is only necessary if the lens has been
installed for the first time or exchanged. In cam-
eras with a MX-B016 ("Hemispheric") lens, the
lens has been focused at the factory.
Check the live image from the camera in the
browser. Activate the focusing aid in the browser (
Focusing Aid
quick
control,
Activated
value).
Carefully turn the lens in clockwise or counter-clockwise direction using
the red lens wrench until the red area of the focusing aid is as small as
possible. Remove the lens wrench every time you changed the lens focus.
Once the focus is adjusted properly, deactivate the focusing aid again
(
Focusing Aid
quick control,
Disabled
value).
3. Adjust viewing direction
Turn the image in the ceiling until the live image
shows the desired viewing direction
1
.
Stick the Allen wrench (item 1.10) into the hole of
the lock screw and loosen the screw a bit
2
.
Stick the blue screwdriver
(item 1.8) into the receptacle for adjust-
ing the camera tilt. Adjust the camera
tilt as needed while watching the live
image of the camera
1
.
Lock the camera tilt by slightly tightening
the lock screw
2
.
4. Configuring and Using the MX-Bus-IO-Module
The camera will automatically detect an installed
MX-Bus-IO-Module (see
Camera Status
,
System
section in browser).
The signal inputs can be used right away in the
signal input profiles
in the
Setup Menu > Event
Overview
. Likewise, the signal outputs can be
used in the
signal output profiles
in
Admin
Menu > Hardware Configuration > Signal Out Profiles
.
In addition, the signal inputs/outputs have been entered automatically
in the
Admin Menu > Assign Wires
dialog and can be used to control
doors and lights.
To use one or both signal outputs not as potential-free outputs (for relays),
but as
self-powered 12 V outputs
, open the
Admin Menu > Hardware
Configuration > Manage Hardware Expansions
dialog. In the
MxBus/
IO Board
section, click on
Connect
for each output you want to use as
self-powered output.
5. Save the configuration
In the live image of the browser, select the
Manage Settings
quick control
ans set
Store Entire Configuration
as value. The camera stores the con-
figuration in the permanent camera memory so that the settings will be
applied at the next camera reboot.
Screw for
locking the
camera tilt
1
2
1
2
Output 1
Output 2
Important Notes
Safety Warnings
• This product must not be used in locations exposed to the dangers
of explosion.
• Make sure that you install this product as outlined in the installation
instructions above.
• When installing this product, make sure that you are only using genuine
MOBOTIX parts and MOBOTIX connection cables.
• Only install this product in suitable, solid materials that provide for a
sturdy installation of the fixing elements used.
• When removing the camera from the ceiling, make sure that the spring
clips do not snap back (
risk of injury!
).
• Electrical systems and equipment may only be installed, modified and
maintained by a qualified electrician or under the direction and supervi-
sion of a qualified electrician in accordance with the applicable electri-
cal guidelines. Make sure to properly set up all electrical connections.
• When attaching modules to the USB connector, the
power consumption
of all attached modules must not exceed 1 W
.
• Due to the high performance of the p25, the area of the image sensor
can get quite hot
, especially when the ambient temperature is also
high. This does not affect the proper functioning of the camera in any
way. This camera must not be installed within the reach of persons.
• Make sure the power supply to the camera is disconnected before
opening the camera housing (e.g., when exchanging the SD card).
• MOBOTIX products include all of the necessary configuration options
for operation in Ethernet networks in compliance with data protection
laws. The operator is responsible for the data protection concept across
the entire system. The basic settings required to prevent misuse can be
configured in the software and are password-protected. This prevents
unauthorized parties from accessing these settings.
• Make sure that the operating temperature of 0 to +40 °C/+32 to +104° F
is not exceeded.
Legal Notes
You must comply with all data protection regulations for video and sound
monitoring when using MOBOTIX products. Depending on national laws
and the installation location of the p25, the recording of video and sound
data may be subject to special documentation or it may be prohibited. All
users of MOBOTIX products are therefore required to familiarize themselves
with all valid regulations and comply with these laws. MOBOTIX AG is not
liable for any illegal use of its products.
Technical Specifications
Since the p25 is identical to the M25 for the most part, the technical data listed in the
M25 Camera Manual in Section Technical Data
also applies to this product. You can find the
M25 Camera Manual as a PDF file on
www.mobotix.com
> Support > Manuals
.
p25 (Differences Compared to M25)
Lens Options
MX-B016 to MX-B237 (180° to 15° hor. angle of view)
Max. Image Size
6MP in 3:2 format (3072x2048)
Audio Functions
None; optionally with microphone and speaker
Interfaces
Ethernet 10/100, IPv4/IPv6, MiniUSB;
MxBus and inputs/outputs using optional
MX-Bus-IO-Module
Power
Consumption
Typ. 4 W
Operating
Conditions
IP20 (DIN EN 60529)
0 to +40 °C/+32 to +104° F (DIN EN 50155)
Max. Thickness for
Installation
Spring clips properly clamp down on materials from 1 to
28 mm/0.04 to 1.1 in
Dimensions
Outside diameter 120 mm/4.72 in, total height
85 mm/3.35 in, height installed 46 mm/1.81 in, recom-
mended min. installation depth 50 mm/1.97 in
Materials
Housing: PBT GF30
Weight
approx. 270 g
MX-Bus-IO-Module
Inputs
2 galvanically separated inputs
(AC/DC, 0 to 48 V)
Outputs
Variant 1 (default):
2 potential-free outputs (max. load
per pin: max. 30 W or max. 1 A or max. 48 V AC/DC)
Variant 2 (set in browser):
2 powered outputs 12 V DC;
max. 50 mA per output
Add. Interfaces
MxBus connections for MOBOTIX peripheral devices
Operating
Conditions
Same as camera
Cross-sectional
area of wires at the
terminals
0.14 mm² – 0.5 mm² (AWG 21 – 26)
Power
Consumption
Typ. 0.5 W, max. 1.5 W
Dimensions/Drilling Template
Outside diameter 120 mm/4.72 in
39 mm/1.54 in
46 mm/
1.81 in
Recommended
min. instal-
lation depth
50 mm/1.97 in
Max. thickness
for installation
28 mm/1.1 in
MX-Bus-IO-Module
p25 main board
Outside diameter 120 mm/4.72 in
25 mm/0.98 in
Cu
t-o
ut
dia
m
ete
r Ø
10
5 m
m
/4
.13
in
