Security-Vision-Systems
EN
MOBOTIX AG • D-67722 Langmeil • Phone: +49 6302 9816-103 • Fax: +49 6302 9816-190 • [email protected]
FlatMount Frame: Quick Install
www
.mobotix.com
Mounting Several FlatMount Frame Units
You can mount several FlatMount Frames next to each other (vertically and horizontally). The delivered
parts of the housing include a connector block, which you can use to combine two housings.
1. Lead Cable into the Housing
«Lead Cable into the Housing» on the front. Since several cable inlets are possible here as well,
make sure that you pierce the inlet that is closest to the required cable connection. The connecting
piece also has a cable inlet. Therefore, you can lead the cable connections of the second housing
through the first housing.
2. Insert Housing
«Insert Housing» on the front. The measurement
for the installation opening depends on the number
of FlatMount Frame units and the required connector
blocks:
(Width of all ho width of connector blocks)
x
112
x
60
mm
.
Set the protective cardboard cover
(included with the delivered parts)
into the housing before pushing it
into the wall cavity. This prevents cement from entering the interior of the housing.
After you have installed the housing into the wall, you can easily remove the carton
by pushing through the pre-cut opening and pulling it out.
112 mm/4.41 in
112 mm/4.41 in
112 mm/4.41 in
22 mm/0.87 in
134 mm/5.28 in
57 mm/
2.24 in
Inserting and Detaching Modules
Insert the Module (Using MxDisplay as an Example)
Make sure that the seal has been positioned properly on the back of the MxDisplay
and the protective foil has been removed. Insert the MxDisplay into the frame with
its right side first (this applies for both the single frame and the FlatMount Frame).
Then push the MxDisplay on the left side into the frame until it clicks into place.
Detach the Module (Using MxDisplay as an Example)
Insert the ruler (included with the FlatMount Frame) into the slit on the lower left
in such a way that the upper part of the ruler is on the same level as the lower
part of the MxDisplay image area. Push the outer end of the ruler downwards
(see adjacent fig.). The MxDisplay is released on the left side, so you can pull it
from the frame.
Copyright © MOBOTIX AG 2014 • Made in Ger
many • T
echnical infor
mation subject to change without notice.
In-wall Installation in Cavities (without In-Wall Housing)
Installations in cavity walls without in-wall housings are possible in
materials that are 3 to 25 mm/0.18 to 1 in thick. For this installation type,
you need to replace the short clamping brackets that are attached to
the FlatMount Frame by the long clamping brackets included with the delivered parts (item 1.2). These
clamping brackets have to be shortened according to the thickness of the material.
1. Replace Clamping Brackets
Prepare the opening for the FlatMount Frame (W x H:
107
x
107
mm
). Measure the thickness of the
material. Cut the long clamping brackets that are included with the FlatMount Frame to the correct
length according to the thickness of the material. Replace the short clamping brackets that are
attached to the FlatMount Frame by the ones you just shortened.
To facilitate the installation, there are notches for the clamping brackets on three
corners of the FlatMount Frame. After you have attached the long clamping brackets
to the frame, turn three of the clamping brackets so that they fit into the notches.
Turn the fourth clamping bracket (on the corner without notch) downwards.
2. Insert FlatMount Frame
Insert the FlatMount Frame into the opening. Make sure that the
red knob is on the lower left corner and that the arrow on the red
knob points at the “open lock” icon. Insert the lower left edge of
the frame first, then follow with the lower right edge. After that,
slightly pull the lower part of the frame back out. This causes the
upper part of the frame to “fall” into the opening.
!
Caution:
In situations, in which a theft protection is not necessary, e.g., indoor installations,
do not
activate the theft protection (the red knob remains in the “open lock” position). If you
twist the knob by mistake, you have to be able to attach a battery (9 V DC). Otherwise, the
frame cannot be released!
3. Tighten Screws
Tighten the screws and make sure that you do not overtighten them. The endings of the clamping
brackets hold the FlatMount Frame to the surface.
