background image

8

 

 

 

 

  

3.Introduction of the gimbal mode 

 

 

In the main interface of the software, click on the image window in the lower left corner to switch the 
map/image window and enlarge the image window. As shown in Figure 10, you can switch the gimbal 
mode  by  clicking  the  gimbal  mode  button  in  the  upper  right  corner  of  the  image  serial 
port:

Following:  In  this  mode,  click  anywhere  in  the  image  screen,  and  the  platform  will  automatically 

follow the target window clicked by the user.

Control: In this mode, the user adjusts the angle of the gimbal 

by controlling the rollers on both sides of the platform.

Back to the middle: In this mode, the platform 

automatically returns to the default median. 

 

Figure 10 Gimbal Mode Window 

  

4.Software Setting 

 

1

 

Flight Setting 

Click  the  Icon  on  the  main  interface: 

  ,

enter  the  software  settings  interface,  the  default  is 

flying  setting interface, as shown in Figure 11: Flight settings:  UAV parameters can  be viewed 
and set in the flight settings interface.

 

 
1 Drag the progress bar of the parameter you need to set directly in the flight setting interface to 
set it, and restart the software to take effect; 
2  Set  the  ground  station  loss,  remote  control  fault,  etc.  in  the  flight  setting  interface  (you  can 
choose to return, return to the takeoff point, continue to execute the route, etc.); 
3 The above parameters have been set at the factory. If you want to modify, please consult our 
company; 
 
 
2) Control settings 
Control settings: In the control settings interface, you can perform throttle mode selection, remote 
control calibration, etc., as shown in Figure 12: 

Summary of Contents for Etlas Mobile

















Reviews: