Fig. 2
•
Remove the gear tray from the baseplate by pinching the clips at two locations (see Fig. 3)
Fig. 3
•
Feed the mains cable through the compression gland provided at the end of the fitting
•
Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown), E
- Earth (green/yellow), N - Neutral (blue) (see Fig. 4)
Fig. 4
•
Align the fitting with the mounting brackets and clip into place
•
Tighten the compression gland ensuring a tight seal is made
•
Replace the gear tray and diffuser ensuring all clips are fastened securely
•
Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class C (TRLED14, TRLED25D, TRLED26D) / D
(TRLED12 / TRLED15 / TRLED15D / TRLED16 / TRLED16D / TRLED22 / TRLED24 / TRLED25 / TRLED26) to
Regulation (EU) No. 2019/2015.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
• Feed the mains cable through the compression gland provided at the end of the fitting
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown),
E - Earth (green/yellow), N - Neutral (blue) (see Fig. 4)
• Align the fitting with the mounting brackets and clip into place
• Tighten the compression gland ensuring a tight seal is made
• Replace the gear tray and diffuser ensuring all clips are fastened securely
• Switch on and check for correct operation
Fig. 3
•
Feed the mains cable through the compression gland provided at the end of the fitting
•
Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown), E
- Earth (green/yellow), N - Neutral (blue) (see Fig. 4)
Fig. 4
•
Align the fitting with the mounting brackets and clip into place
•
Tighten the compression gland ensuring a tight seal is made
•
Replace the gear tray and diffuser ensuring all clips are fastened securely
•
Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of
Fig. 3
Fig. 4
