SENSOR SETUP
DETECTION DIAGRAM
• Please see Fig 3 for sensor adjustments
• Replace back cover
• Switch on power supply and check for correct operation
Fig 2
Fig 3
OS0014 series
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
OS0014, OS0014B
SAFETY
•
Installation of this sensor should only be carried out by a qualified electrician or competent person to the
latest Building and current IEE Wiring Regulations (BS7671)
•
Please isolate mains prior to installation/maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
•
This product is Class II double insulated
•
This product is IP44 rated
INSTALLATION
•
Provide power to the required point of installation. Suitable IP rated junction boxes should be used where
required
•
We recommend an installation height of between 1.8m and 2.5m
•
Remove the back cover by removing screw, (see Fig 1) to access the terminal block
Fig 1
•
Using the sensor as a template mark the location of the fixing holes, and drill the holes ensuring not to infringe
with any joists, gas or water pipes or electrical cables
•
Connect the sensor to the luminaire and mains supply (via terminal connector) ensuring the correct polarity is
observed. See Fig 2 for the wiring diagram (Live (brown), Neutral (blue) and Switched Live (A))
Fig 2
•
Please see Fig 3 for sensor adjustments
•
Replace back cover
•
Switch on power supply and check for correct operation
Remove screw
(N) Neutral (blue)
(L) Live (brown)
N
A
L
Load/
luminaire
(A) Red
Time
Lu
x
SENSOR SETUP
Fig 3
DETECTION DIAGRAM
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.
Irreparable damage will occur if this instruction is not followed.
GENERAL
The unit should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where
facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the sensor.
Warranty
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the current
edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this
product should fail within its warranty period it should be returned to the place of purchase for a free of charge
replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement
product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior
notice.
Mounting height
1.8m-2.5m
-
+
Min 10sec
+ 3sec
Max 15min
3
min
3lx
2000lx
Lux
Time
up to
12m
Floor
Wa
ll
3
SENSOR SETUP
Fig 3
DETECTION DIAGRAM
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.
Irreparable damage will occur if this instruction is not followed.
GENERAL
The unit should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where
facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the sensor.
Warranty
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the current
edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this
product should fail within its warranty period it should be returned to the place of purchase for a free of charge
replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement
product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior
notice.
Mounting height
1.8m-2.5m
-
+
Min 10sec
+ 3sec
Max 15min
3
min
3lx
2000lx
Lux
Time
up to
12m
Floor
Wa
ll
±
