MK Diamond Products MK-Scarifier SG-5 Owner'S Manual Download Page 45

Page: 45 / 52

MK-Scarifier MaiNTeNaNce

V-Belt inspection, adjustment and replacement

(A)

Remove the Cutting

Drum (See Cutting Drum

Change-out).

(B)

Locate and remove the Belt

Guard Retaining Screws us-

ing a 9/16-wrench.

(C)

Remove the Belt Guard.

(D)

Inspect the V-belt for exces-

sive wear, cracks and cuts –

if worn, proceed to step F.

(E)

Check V-belt for proper ten-

sion, if tension correct, go to

step O (proper tension is 1/2-

inch deflection of the belt).

(F)

Locate the Engine Mounting

Plate Bolts on both sides.

(G)

Loosen the Front Engine

Mounting Plate Bolts on

both sides using a 9/16-inch

wrench.

(H)

Loosen the Rear Engine

Mounting Plate Bolts on

both sides using a 9/16-inch

wrench.

(I)

Locate the V-belt Adjusting

Screw Lock Nut inside

the Cutting Drum Well.

Loosen the nut using a

9/16-inch wrench.

NOTe:

When a new belt is installed, it should be inspected and re-tensioned after the first forty-eight

(48) hours of operation.

In order to ensure the Scarifier operates at peak efficiency, the power transmission V-belt should be

inspected monthly and changed if any signs of damage and/or excessive wear is observed.

Summary of Contents for MK-Scarifier SG-5





















































Search results

Summary of Contents for MK-Scarifier SG-5

Reviews:

Related manuals for MK-Scarifier SG-5

Brands by name

Popular brands

MK Diamond Products MK-Scarifier SG-5, Owner'S Manual

Search results

Summary of Contents for MK-Scarifier SG-5

Reviews:

Related manuals for MK-Scarifier SG-5

Brands by name

Popular brands