Mizuho MOS-1302B Operator'S Manual Download Page 45

Page: 45 / 86

Operation

Adjustment of leg plate

The left and right leg plates can be operated

separately. They can be flexed down in 15° increments

to 6 different positions (max. 90°), flexed up in 15°

increments to 2 different positions (max. 30°), swung

outward (max. 90°), and can be detached.

Flexing

2. Hold the front edge of the leg plate and flex the

leg plate downward or upward.

1. Hold the edge of the leg plate and loosen the leg

plate flexing handle.

Swinging outward

2. Hold the front edge of the leg plate and swing

outward the leg plate to desired position.

1. Loosing the leg plate fixing handle.

3. Tighten the leg plate fixing handle at the desired

position.

WARNING

- When flexing the leg plate, be

sure to hold the front edge of

the leg plate before turning the

handle.

Otherwise the leg plate may

drop down and cause injury.

- Make sure to tighten the leg

plate flexing handle and fixing

handle securely. If the leg plate

moves, the patient may get

injured.

3. Tighten the leg plate flexing handle when a

desired angle is achieved.

Leg plate flexing handle

Leg plate

fixing handle

Summary of Contents for MOS-1302B























































































Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands

Mizuho MOS-1302B, Operator'S Manual

Search results

Summary of Contents for MOS-1302B

Reviews:

Related manuals for MOS-1302B

Brands by name

Popular brands