manualshive.com logo in svg

Mizuho Allegro 6800, Owner'S Manual, Page: 17 / 61

Share
Download
Mizuho Allegro 6800 Owner'S Manual Download Page 17

MIZUHOSI 2009 

NW0510 Rev. D 

17 

6.0  FUNCTION CHECK 

 

Perform all steps in this procedure. If you have any questions please feel free to contact 
Mizuho  OSI  Customer  Resource  Group  at  800-777-4674,  7AM  to  5PM  PST.  For  a 
complete  definition  of  reference  terms  used  in  this  procedure,  please  refer  to  the 
Glossary of Terms (Section 2) this owners manual. 
 

6.1 Function Check 

 

1.  Plug a hand pendant into the desired location.   
 

NOTE:

  A hand pendant can be plugged in at the pedestal end (back) or the cantilever 

end (front) of the base, or both locations with two hand pendants.  If a hand pendant is 
removed  or  added  while  the  table  is  operational,  the  table  must  be  shut  down  for  30 
seconds.  When turned back on, the floor locks must be reengaged. 

 
2.  Plug  in  and  tighten  the  connector  for  the  joystick  into  the  receptacle  labeled 

JOYSTICK at either end of the pedestal.  

 
3.  Attach and correctly orient the locking lever on the joystick.  This lever must always 

lock in place toward the pedestal end of the table.  Correct orientation of this lever 
ensures  the  direction  of  travel  of  the  Allegro™  6800  will  be  consistent  with  the 
direction of the joystick movement. 

 
4.  If  the  table  is  to  be  used  under  battery  power,  ensure  that  the  battery  has  been 

properly  charged  and  that  the  battery  status  LED  on  the  hand  pendant  is  green 
when the on/off power switch is on.    

 
5.  If  the  table  is  to  be  used  under  line  power,  plug  in  power  cord  into  an  appropriate 

hospital  grade  outlet  and  turn  on  the  main  ON/OFF  power  switch.  Note  that  the 
switch illuminates indicating that AC power is on.  

 
6.  Lockout  mode:  The

 

Allegro™  6800  is  only  operational  if  the  LOCKED  WHEN  LIT 

green indicator located on the control panel is illuminated and the FLOOR LOCK ON 
LED is illuminated on the hand pendant. Verify that the hand pendant functions do 
not operate except to activate floor locks. 

 
7.  Floor lock check using the control panel: 

7.1. 

Press and hold DOWN TO LOCK button until green locked when lit indicator 
is illuminated on the control panel and that the FLOOR LOCK ON LED on the 
hand  pendant  is  illuminated.  Table  is  locked  if  it  cannot  be  moved  on  its 
wheels. 

7.2. 

Press and hold UP TO UNLOCK button until amber indicator is illuminated on 
the control panel and the FLOOR LOCK STOWED indicator is illuminated on 
the hand pendant. The table is unlocked if it can move on its wheels. 

 

Summary of Contents for Allegro 6800






























































Reviews:

No comments