Mitsubishi S12A2-PTA2, Operation & Maintenance Manual

Page: 16 / 90

CONTENTS
CONTENTS-4
List of Illustrations
Fig. 2-1 Engine Front View ............................... 2-1
Fig. 2-2 Engine Rear View................................. 2-1
Fig. 2-3 Engine Left Side View ......................... 2-2
Fig. 2-4 Engine Right Side View ....................... 2-2
Fig. 2-5 Manual Stop Lever .............................. 2-3
Fig. 2-6 Stop Solenoid ....................................... 2-3
Fig. 2-7 Oil Pressure Unit ................................. 2-4
Fig. 2-8 Revolution Detection Pickup ............... 2-4
Fig. 2-9 Oil Pressure Switch .............................. 2-5
Fig. 2-10 Oil Filter Alarm Switch .......................... 2-5
Fig. 3-1 Priming Pump - Handle ........................ 3-2
Fig. 3-2 Fuel Filters (Wire-element Type)
- Bleed Air............................................. 3-2
Fig. 3-3 Fuel Filter - Bleed Air............................ 3-2
Fig. 3-4 Fuel Injection Pump - Bleed Air ........... 3-3
Fig. 3-5 Priming Pump Tightening Method ....... 3-3
Fig. 3-6 Priming Pump Head Packing .............. 3-3
Fig. 3-7 Oil Filler and Oil Level Gauge .............. 3-4
Fig. 3-8 Pouring Engine Oil on Valve Mechanisms
and Chamber ....................................... 3-4
Fig. 3-9 Radiator Cap ........................................ 3-5
Fig. 3-10 Coolant Drain Cock (Engine)................ 3-5
Fig. 3-11 Coolant Drain Cock (Water Pump)....... 3-5
Fig. 3-12 Battery Electrolyte Level - Inspect ....... 3-6
Fig. 3-13 Valves for Open/Closed Position
- Check ................................................ 3-8
Fig. 3-14 Fuel Control Link - Check .................... 3-9
Fig. 3-15 Oil Filler and Oil Level Gauge ............ 3-10
Fig. 3-16 Thermo label of damper ..................... 3-11
Fig. 3-17 Manual Stop Lever ............................ 3-14
Fig. 5-1 Engine Oil Grade.................................. 5-1
Fig. 5-2 Selection of Oil Viscosity ...................... 5-3
Fig. 6-1 GLASSY - LLC ..................................... 6-1
Fig. 8-1 Adjusting the Belt Tension ................... 8-2
Fig. 8-2 Damper - Check Visually...................... 8-3
Fig. 8-3 Damper Temperature Management ..... 8-4
Fig. 8-4 Fuel Tank - Drain Water ....................... 8-5
Fig. 8-5 Gauze Filter - Clean ............................. 8-6
Fig. 8-6 Fuel Filters (Wire-element Type)
- Drain Water ...................................... 8-7
Fig. 8-7 Inside of Fuel Filters (Wire-element Type)
- Clean...................................................8-7
Fig. 8-8 Fuel Filter - Replace..............................8-8
Fig. 8-9 Fuel Filter ..............................................8-8
Fig. 8-10 Ball Joints For Looseness - Inspect ......8-9
Fig. 8-11 Fuel Control Link - Remove...................8-9
Fig. 8-12 High Pressure Fuel Injection Pipe and
Clamp Seat - Inspect and Replace .....8-10
Fig. 8-13 Low Pressure Fuel Pipe and Clip
- Inspect ..............................................8-10
Fig. 8-14 Oil Filler and Oil Level Gauge .............8-12
Fig. 8-15 Oil Filter and Bypass Oil Filter
- Replace.............................................8-13
Fig. 8-16 Oil Filter...............................................8-13
Fig. 8-17 Oil Pipe and Clip - Inspect and
Replace ...............................................8-14
Fig. 8-18 Radiator Cap .......................................8-15
Fig. 8-19 Coolant Drain Cock (Engine)...............8-15
Fig. 8-20 Coolant Drain Cock (Water Pump)......8-16
Fig. 8-21 Radiator Fins - Clean ..........................8-17
Fig. 8-22 Turbocharger - Inspect .......................8-18
Fig. 8-23 Pre-cleaner - Clean .............................8-18
Fig. 8-24 Battery Electrolyte Level - Inspect ......8-19
Fig. 8-25 Specific Gravity of Battery Electrolyte
- Check................................................8-19
Fig. 8-26 Starter - Inspect...................................8-20
Fig. 8-27 Alternator - Inspect..............................8-20
Fig. 10-1 Hanger ................................................10-1