Mitsubishi PAJERO IV Service Manual Download Page 20

Page: 20 / 72

ROAD TEST

PRE-DELIVERY INSPECTION

1-14

ROAD TEST

27. ENGINE PERFORMANCE AND
EXHAUST GAS

M6010800100023

1. Engine performance

Check the engine for proper performance and
accelerator pedal for smooth operation.

2. Exhaust system

(1) Check the exhaust system components for

gas leaks.

(2) Verify that no black smoking is emitted from

the end of the exhaust pipe (diesel-powered
vehicles).

28. TRANSMISSION IN ALL RANGES

M6010800200020

1. Manual transmission

Check the transmission in all forward ranges and
in reverse.

2. Automatic transmission

(1) Make sure shift indicator lines up properly in

all ranges.

(2) Depress the accelerator completely to check

that the manual kickdown is operating

correctly.

(3) Stop the vehicle on a steep incline.

Put the automatic transmission in "P" position

and slowly release the service brakes to see if

"P" position lock holds. If it does not hold, the

transmission requires further service.

29. BRAKES

M6010800300027

1. Service Brake

Put the vehicle in gear and apply the brakes while
the vehicle is in motion. Be sure brake operation
is smooth and positive.

2. Parking Brake

(1) Stop the vehicle on a steep incline.

With the service brakes firmly applied, place
the transmission in "N" position, and set the
parking brakes.

(2) Slowly release the service brakes to see if the

parking brakes will hold.

30. STEERING CONTROL

M6010800400024

1. Check for excessive play or looseness.
2. Check the steering wheel centre.

AC305633

AC305634

AC305635

Button

AC305636

Summary of Contents for PAJERO IV









































































Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands

Mitsubishi PAJERO IV, Service Manual

Search results

Summary of Contents for PAJERO IV

Reviews:

Related manuals for PAJERO IV

Brands by name

Popular brands