Mitsubishi Melsec FX-4AD User Manual Download Page 5

Page: 5 / 14

Preset 0 (-10V to +10V)

Preset 1 (+4mA to +20mA)

Preset 2 (-20mA to +20mA)

Analog inputs continued.....

Digital
Output

+1600

+1000

+32mA

+20mA

-1000

-1600

-20mA

-32mA

Current
Input

+1750

+1000

+32
mA

+20
mA

+4
mA

Digital
Output

Miscellaneous

Item

Specification

Isolation

Photo-coupler isolation between analog and digital circuits.

DC/DC converter isolation of power from FX base unit.

No isolation between analog channels.

Number of occupied I/O points

8 points taken from the FX expansion bus (can be either inputs or outputs)

Digital
Output

+10V

+10.235V

Voltage Input

+2047
+2000

-10.24V

-10V

-2000

-2048

NOTE: Preset ranges are selected by an appropriate setting in buffer memory of the analog block.
Current/Voltage input selection must match the correct input terminal connections.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Melsec FX-4AD















Search results

Summary of Contents for Melsec FX-4AD

Reviews:

Related manuals for Melsec FX-4AD

Brands by name

Popular brands

Mitsubishi Melsec FX-4AD, User Manual

Search results

Summary of Contents for Melsec FX-4AD

Reviews:

Related manuals for Melsec FX-4AD

Brands by name

Popular brands