5
[Example 1]
When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation
marks are ASCII codes.):
Sending commands
Status code from
Description
from the PC, etc.
the projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
'
picture control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D
Command receipt confirmation
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '
'
(Command echo back)
Sending commands
Status code from
Description
from the PC, etc.
the projector
30 30 41 50 4F 4E 31 0D
Command for setting the
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
AUTO POWER ON to ON
30 30 41 50 4F 4E 31 0D
Command receipt confirmation
'0' '0' 'A' 'P' 'O' 'N' '1' '
'
(Command echo back)
[Example 3]
When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed
in quotation marks are ASCII codes.):
Sending commands
Status code from
Description
from the PC, etc.
the projector
30 30 53 0D
Command for checking
'0' '0' 'S' '
'
the TINT setting
30 30 53 2B 31 30 0D
Check result (+10)
'0' '0' 'S' '+' '1' '0' '
'
• To set TINT at 0, enter +00. (-00 is invalid.)
[Example 4]
When setting the REFERENCE of GAMMA MODE-USER1 to CINEMA (+2), ADJUST MODE
to RED (R), HIGH to -2, MID to +3 and LOW to 0. (Figures and symbols enclosed in quotation
marks are ASCII codes.):
* There is no command for selecting ALL for ADJUST MODE. Even when you want to set all
the three colors to the same value, send a command for each of R, G, and B respectively.
Sending commands
Status code from
Description
from the PC, etc.
the projector
30 30 47 53 55 31 52 2B 32 2D 30 32 2B 30 33 2B 30 30 OD
Command for setting GAMMA
'0' '0' 'G' 'S' 'U' '1' 'R' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '
'
MODE-USER1
30 30 47 53 55 31 52 2B 32 2D 30 32 2B 30 33 2B 30 30 OD Command receipt confirmation
'0' '0' 'G' 'S' 'U' '1' 'R' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '
'
(Command echo back)
[Example 2]
When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0,
and the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII
codes.):
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII
'+'
'–'
'0'
'1'
'2'
'3'
'4'
'5'
'6'
'7'
'8'
'9'
HEX
2Bh
2Dh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
*1
) Setting range differs depending on the input signals.
• Some commands are not executed depending on the input signal. The operational restrictions same as
those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.
ITEM
ASCII
HEX
VALUE
CLAMP POSITION
CLP
43h
4Ch
50h
001
-
255
CLAMP WIDTH
CLW
43h
4Ch
57h
01
-
63
VERT.SYNC.
VSC
56h
53h
43h
0
(OFF),
1
(AUTO)
LPF
LPF
4Ch
50h
46h
0
(OFF),
1
(ON)
SHUTTER(U)
SHU
53h
48h
55h
00 - 32
SHUTTER(L)
SHL
53h
48h
4Ch
00 - 32
SHUTTER(LS)
SHLS
53h
48h
4Ch
53h
00 - 95
SHUTTER(RS)
SHRS
53h
48h
52h
53h
00 - 95
