Mitsubishi FX1N-5DM User Manual Download Page 4

Page: 4 / 7

HEAD OFFICE

: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310 JAPAN

HIMEJI WORKS : 840, CHIYODA CHO, HIMEJI, JAPAN

This manual confers no industrial
property rights or any rights of any other
kind, nor does it confer any patent
licenses. Mitsubishi Electric Corporation
cannot be held responsible for any
problems involving industrial property
rights which may occur as a result of
using the contents noted in this manual.

Guidelines for the safety of the user and protection of the Micro Display Module FX

-5DM

•

This manual has been written to be used by trained and competent personnel. This is defined by the European directives for machinery, low voltage and EMC.

•

If in doubt at any stage during the installation of the Micro Display Module FX

-5DM always consult a professional electrical engineer who is qualified and trained to the

local and national standards. If in doubt about the operation or use of the Micro Display Module FX

-5DM please consult the nearest Mitsubishi Electric distributor.

•

Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment.

•

All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative examples.

•

Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

5. Operation List

The process for the operator functions are shown below.

•

The operation keys are expressed as follows.

: ESC key

ESC

: "-" key

: "+" key

: OK key

Press and hold
it for 2 seconds
or more.

-1

Determine
the input.

TCD
XYMS

➂

An item being changed flickers.
Set "year, month, day, hour and minute" in this order.
When the OK key is pressed at "minute" set up, the setting operation will be completed.

Select an either device using the "+" and "-" keys.
(In the initial status, "D" flickers.)
T, C, D (16-bit), D (32-bit), X, Y, M, S or BFM

"-" key

"+" key

Determine
the input.

* "BFM" is displayed only when the FX

Series PLC is used.

➀

➁

➀

➂

RUN

( E r r o r d i s p l a y )

Refer to error display.

Program error

Keyword error
(Entry code error)

➁

➂

➀

➁

➂

➃

Set or reset the bit
device.

From the displayed device No., the ON/OFF
status of 8 points (in the case of X or Y) or 10
points (in the case of M or S) is indicated.
: OFF status

: ON status

Forced set/reset mode
A selected device is indicated with underline.

Underline flickers.

Select a device No.

Eight points (in the case of X or Y) or 10 points
(in the case of M or S) are scrolled at a time.
"+" key: Scrolls toward larger device Nos.
"

" key: Scrolls toward smaller device Nos.

The current ON/OFF status is reversed.
*

➀

➁

➂

➃

➄

The device turns on and off alternately when the OK key is
pressed.
If the OK key is pressed while the device is ON, it turns off.
If the OK key is pressed while the device is OFF, it turns on.

➄

RUN

If a special block is connected to the FX1N Series when you select a device, a buffer memory (hereafter referred to as "BFM") is
displayed. A displayed numeric value indicates the unit No.
When you press the OK key, BFM monitor starts for the unit having the displayed unit No.
The BFM No. is displayed. The BFM current value is displayed. Select the BFM No.
After pressing the OK key, you can change the value of the displayed BFM No. Every time you press and hold the OK key for 2
seconds or more, the display changes over alternately between 16-bit BFM and 32-bit BFM.
Increase or decrease the BFM current value using the "+" or "-" key.
Write the data you have input to the BFM.

CAUTION
Depending on the type of the connected special block, the BFM is cleared when the power is turned off or the mode is changed
over between RUN and STOP. When using a special unit, write the data finally to the BFM using a sequence program (using FNC
79 TO instruction (write to BFM).)

➀
➁

➂

➅

➃

➄

S: State

T: Timer

BFM

Press and hold
for 2 sec or more.

➀

➁

➂

➃

➄

➅

➆

➇

➆

➇

Time display screen (when the power is turned on)

➀

Current value

C
S

Set value

➁

➂

Press the "+" or "-" key to change over the current value and the set value. For the set value, "S" is added in a
right position above the device No.
When the OK key is pressed, the current value or the set value is changed.
Press the "+" key to increase the value. Press the "-" key to decrease the value.
Press the OK key to determine the input. At this time, the input data is written to the PLC.
When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value
is reset to "0" and the contact turns off.
When the OK key is pressed once again, the current value reset operation will be completed.

➁

➀

➂
➄

RUN

➄

Press and hold it for
2 seconds or more.

Determine
the input.

➃

➂

➃

➁

➀

D is scrolled by 1 point at a time.
Select the current value change mode.
Press the "+" key to increase the value. Press the "-" key to decrease the value.
Press the OK key to determine the input. At this time, the input data is written to the PLC.

➀

➁

➂

➃

RUN

➀

➁

➀

Error step No.

➁

Error code

Press the ESC key or
release the error status to
delete the error display.

When an keyword (entry code) has been input to the PLC, only the
time can be displayed.
If you press the OK key while the time is displayed, the error message
shown on the left flickers for 5 seconds.
Release the keyword (entry code) in a peripheral unit such as
the FX-10P/20P and the personal computer software for creating
sequence programs.

➂

➀

➁

Changing the
current value

Changing the
set value

OK OK

➃

"ON" is displayed when T or C is ON and "R" is displayed while resetting.
Change over the device to monitor.
T or C that is not used in the program is not displayed.
(A horizontal line "-" is displayed if there is none of T or C in the program.)
When the OK key is pressed once, the current value is changed, and when the OK key is pressed three times, the set value is changed. (Flickers while changing)
Press the "+" key to increase the value. Press the "-" key to decrease the value.
Press the OK key to determine the input. At this time, the input data is written to the PLC.
When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off.
When the OK key is pressed once again, the current value reset operation will be completed.

RUN

➁

➀

➂

➃

➄

➅

Press and hold it for
2 seconds or more.

➄

➅

Determine
the input.

➅

➂

➁

➃

D is scrolled by 2 points at a time by the "+" key and by 1 point at a time by the "-" key.
Select the current value change mode.
Press the "+" key to increase the value. Press the "-" key to decrease the value.
Press the OK key to determine the input. At this time, the input data is written to the PLC.

➀

➁

➂

➃

RUN

➀

Manual number : JY992D84901

Manual revision : E

Date

: June 2008

JY992D84901E

Effective June 2008