Mitsubishi ECLIPSE CROSS 2017 Owner'S Manual Download Page 397 | Manualshive

Page: 397 / 538

background image

FULL

LOW

*: Front of the vehicle

5. Add coolant to the radiator and/or re-

serve tank if necessary. (Refer to the
“Maintenance” section.)

WARNING

l

Make  sure  that  the  engine  has  cooled
down  before  removing  the  radiator  cap
(C),  because  hot  steam  or  boiling  water
otherwise  will  gush  from  the  filler  port
and may scald you.

CAUTION

l

Do not add coolant while the engine is hot.
Suddenly adding cold coolant could damage
the engine. Wait for the engine to cool
down, then add coolant a little at a time.

6. Examine the radiator hoses for coolant

leakage and the drive belt for looseness
or damage.
If there is anything wrong with the cool-
ing system or drive belt, we recommend
you to have it checked and repaired.

Tools and jack*

E00800902800

Storage

The  tools  and  jack  are  stored  under  the  lug-
gage floor board of the luggage compartment.
The  storage  location  of  the  tools  and  jack
should  be  remembered  in  case  of  an  emer-
gency.

Vehicles with spare wheel

1- Tools

2- Jack

Vehicles with tyre repair kit

1- Tools
2- Jack

Tools

1- Jack bar
2- Wheel nut wrench

Tools and jack*

8-05

OGKE18E1

For emergencies

8

«
...
395
396
397
398
399
...
»

Summary of Contents for ECLIPSE CROSS 2017



























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ECLIPSE CROSS 2017

Reference Series

Brand: OEM Audio Pages: 29

Sprinter Bed System Adventure Wagon Kit

Brand: FVC Pages: 8

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: Volvo Pages: 266

Brand: Toyota Pages: 600

Brand: Mazda Pages: 1001

Brand: Prorack Pages: 13

Brand: Subaru Pages: 2

Brand: Connects2 Pages: 2

Brand: DRAGONFIRE Pages: 4

Brand: Nos Pages: 22

Brand: Yakima Pages: 12

Brand: Rally Armor Pages: 4

10-8002-C12167A

Brand: Saleen Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands