manualshive.com logo in svg

Mitsubishi Heavy Industries EEVKIT6-E-C/A, Technical Manual

Share
Download
Mitsubishi Heavy Industries EEVKIT6-E-C/A Technical Manual Download Page 21

-

 19 

-

 '19 • KX-T-336

3.4  Switching return/supply air temperature control

Normal KX indoor unit’s are control by 
their EEV’s to keep system reliability.

[ Cooling ] Superheat (SH)

[ Heating ] Subcool (SC)

Return

/

supply air temperature control

Cooling mode and heating mode must use same pressure control mode.
(STANDARD mode or TYPE1 mode)

SC

= CT – liquid temp

erature

 at EEV

SC

Thi-R1

Thi-R2

Thi-R3

Gas

Liquid

Heating

Flow

Flow

Thi-R1

Thi-R3

Thi-R2

SC

Thi-R1

Thi-R2

Thi-R3

Gas

Liquid

SH

Mixed

Cooling

Flow

Flow

Te

m

perature

Te

m

perature

Thi-R1

Thi-R3

Thi-R2

SH

Enthalpy

P

re

ss

ur

e

Evaporator

Condenser

Condensed 

temperature (CT)

Evaporated 

temperature (ET)

Compressor

EEV

SH

SC

SH

=Compressor suction temperature – ET 

Control

Pressure control

mode

Target pressure / supply

air temperature setting guideline

Return air temperature 
control

STANDARD

Evaporating temperature: 5-12

℃

Condensing temperature: 42-47

℃

TYPE1

Evaporating temperature: 5-12

℃

Condensing temperature: 32-37

℃

Supply air temperature 
control

STANDARD

Cooling supply air temperature: 

12-18

℃

Heating supply air temperature: 

32-40

℃

STANDARD
(SW7-2 ON)

Cooling supply air temperature: 

12-18

℃

Heating supply air temperature: 

20-28

℃

TYPE1

Cooling supply air temperature: 

22-28

℃

Heating supply air temperature: 

20-28

℃

Summary of Contents for EEVKIT6-E-C/A







































Reviews:

No comments

Brands by name

Popular brands

Load more brands