Mitsubishi Electric NZ2GF2B-60TCRT4, User Manual

Page: 318 / 388

316
(c) Resolution
The resolution is applied to the stored values and the set values of particular remote buffer memory areas as
described in the following table.
For applicable remote buffer memory areas, refer to the following.
 Page 362, Appendix 3 (68)
(d) When Auto-setting at input range change (address: 1H. b0) is Enable (1)
When the input range is changed, the following remote buffer memory areas are set automatically according to
selected temperature sensor. Set the remote buffer memory areas again if necessary.
At the same time, the following remote buffer memory areas related to the input range is initialized to the
default value (0) automatically. Set the remote buffer memory areas again if necessary.
The remote buffer memory areas listed above are automatically set when CH  Input range (address: 100H,
130H, 160H, 190H) is changed and Initial data setting request flag (RY9) is turned on and off.
(e) When Auto-setting at input range change (address: 1H. b0) is Disable (0)
Sometimes the setting value of remote buffer memory (

Page 316, (5) (d)) might be out of setting range.
(When the setting range changes according to the change of the input range, the set value before the change
can turn out of the range.) In this case, a write data error (error code: 0004H) occurs in the remote buffer
memory area where the value turns out of the setting range. Change the input range after setting each remote
buffer memory area with values within the setting range after the input range change.
Resolution Stored value Set value
1 Value in 1

(

or digit) unit is stored. Set a value in 1

(

or digit) unit.
0.1 Value in 0.1  (  ) unit (tenfold value) is stored. Value in 0.1  (  ) unit (tenfold value).
Remote buffer memory area name
Remote buffer memory address
Reference
CH1 CH2 CH3 CH4
CH

Upper limit setting limiter 10AH 13AH 16AH 19AH
Page 325, Appendix 3 (14)
CH  Lower limit setting limiter 10BH 13BH 16BH 19BH
CH  Process alarm lower lower limit value 251H 25AH 263H 26CH
Page 350, Appendix 3 (47)
CH  Process alarm lower upper limit value 252H 25BH 264H 26DH
CH

Process alarm upper lower limit value 253H 25CH 265H 26EH
CH  Process alarm upper upper limit value 254H 25DH 266H 26FH
Remote buffer memory area name
Remote buffer memory address
Reference
CH1 CH2 CH3 CH4
CH  Set value (SV) setting 101H 131H 161H 191H Page 317, Appendix 3 (6)
CH  Loop disconnection detection dead band 117H 147H 177H 1A7H Page 335, Appendix 3 (26)
CH  Alert set value 1 224H 22CH 234H 23CH
Page 348, Appendix 3 (45)
CH  Alert set value 2 225H 22DH 235H 23DH
CH  Alert set value 3 226H 22EH 236H 23EH
CH  Alert set value 4 227H 22FH 237H 23FH
CH  Sensor two-point correction offset value (measured value) 284H 288H 28CH 290H Page 352, Appendix 3 (52)
CH  Sensor two-point correction offset value (corrected value) 285H 289H 28DH 291H Page 353, Appendix 3 (53)
CH  Sensor two-point correction gain value (measured value) 286H 28AH 28EH 292H Page 353, Appendix 3 (54)
CH  Sensor two-point correction gain value (corrected value) 287H 28BH 28FH 293H Page 354, Appendix 3 (55)
CH  AT bias setting 2A1H 2A3H 2A5H 2A7H Page 355, Appendix 3 (57)
CH  Simultaneous temperature rise gradient data 2D1H 2D5H 2D9H 2DDH Page 357, Appendix 3 (60)
CH  Simultaneous temperature rise dead time 2D2H 2D6H 2DAH 2DEH Page 358, Appendix 3 (61)