Mitsubishi Electric MUZ-FH25VE Service Manual Download Page 31

Page: 31 / 54

No. Symptom LED

indication Abnormal point/

Condition

Condition Remedy

Outdoor unit

operates.

7-time

ash

2.5 seconds OFF

Low discharge tem-

perature protection

Temperature of discharge temperature thermistor has been

50°C or less for 20 minutes.

Refer to 11-5. "Check of LEV".

Check refrigerant circuit and refrig-

erant amount.

•

8-time

ash

2.5 seconds OFF

MUZ-FH25/35

PAM protection

PAM: Pulse Ampli-

tude Modulation

The overcurrent

ows into PFC (Power factor correction :

IC820) or the bus-bar voltage reaches 394 V or more, PAM

stops and restarts.

This is not malfunction. PAM pro-

tection will be activated in the fol-

lowing cases:

1 Instantaneous power voltage

drop. (Short time power failure)

2 When the power supply voltage

is high.

MUZ-FH50

Zero cross detecting

circuit

Zero cross signal cannot be detected.

It occurs with following cases.

1 Instantaneous power voltage

drop. (Short time power failure)

2 Distortion of primary voltage

Refer to 11-5. "Check of power

supply".

•

9-time

ash

2.5 seconds OFF

Inverter check mode The connector of compressor is disconnected, inverter check

mode starts.

Check if the connector of the com-

pressor is correctly connected.

Refer to 11-5. "How to check

inverter/compressor".

•

NOTE:

1. The location of LED is illustrated at the right

gure. Refer to 11-6.1.

2. LED is lighted during normal operation.

The

ashing frequency shows the number of times the LED blinks after every 2.5-second OFF.

(Example) When the

ashing frequency is “2”.

OFF

2.5-second OFF

0.5-second ON

LED

Flashing

→

MUZ-FH25/35VE

Inverter P.C. board

MUZ-FH50VE

LED

→

Flashing

OBH624A

Summary of Contents for MUZ-FH25VE























































Search results

Summary of Contents for MUZ-FH25VE

Reviews:

Related manuals for MUZ-FH25VE

Brands by name

Popular brands

Mitsubishi Electric MUZ-FH25VE, Service Manual

Search results

Summary of Contents for MUZ-FH25VE

Reviews:

Related manuals for MUZ-FH25VE

Brands by name

Popular brands