manualshive.com logo in svg

Mitsubishi Electric MSZ-CB22VA, Service Manual, Page: 24 / 36

Share
Download
Mitsubishi Electric MSZ-CB22VA Service Manual Download Page 24

24

DISASSEMBLY INSTRUCTIONS

10

(1)  Slide the sleeve and check if there is a locking lever or not.

(2) The terminal with this connector has the 
      locking mechanism.

1

Slide the sleeve.

2

Pull the terminal while 

   pushing the locking
   lever.

1

Hold the sleeve, and 

   pull out the terminal 
   slowly.

The terminal which has the locking mechanism can be detached as shown below.
There are two types ( Refer to (1) and (2)) of the terminal with locking mechanism.
The terminal without locking mechanism can be detached  by pulling it out.
Check the shape of the terminal before detaching.

<"Terminal with locking mechanism" Detaching points>

Connector

Sleeve

Locking lever

MSZ-GA22VA

MSZ-GA25VA

MSZ-GA35VA

INDOOR UNIT

OPERATING PROCEDURE

PHOTOS

Photo 1

1.  Removing the panel

(1) Remove the horizontal vane. 
(2) Remove the screw caps of the panel.

Remove the screws. (See Photo 1.)

(3) Hold the lower part of both ends on the panel and pull it 

slightly toward you, and then remove the panel by pushing 
it upward.

Screws of the panel

Horizontal vane

OB378C--1.qxp  07.3.30 8:35 AM  Page 24

Summary of Contents for MSZ-CB22VA





































Reviews:

No comments