Mitsubishi Electric MSY-GW25VFD, Operating Instructions Manual

Page: 5 / 16

En-4
Remote controller
Remote controller holder
Signal transmitting
section
Distance of signal :
About 6 m
Beep(s) is (are) heard from
the indoor unit when the
signal is received.
Operation
display section
OFF/ON
(stop/operate) button
Temperature
buttons
Page 5
Operation
select button
Page 5
ECONO COOL
button
Page 8
FAN speed control
button
Page 6
LONG button
Page 7
<only GW50/60/71/80>
WIDE VANE control
button
Page 6
<only GW50/60/71/80>
VANE control button
Page 6
TIME, TIMER set buttons
Page 4, 8
Increase time
Decrease time
CLOCK button
Page 4
RESET button
Page 4
Lid
Slide the lid down to open
the remote controller. Slide
it down further to get to the
weekly timer buttons.
• Install the remote
controller holder in a
place where the signal
can be received by the
indoor unit.
• When the remote
controller is not used,
place it in this holder.
Only use the remote controller provided
with the unit.
Do not use other remote controllers.
If two or more indoor units are installed
in proximity to one another, an indoor
unit that is not intended to be operated
may respond to the remote controller.
i-save button
Page 7
WEEKLY TIMER
set buttons
Page 9
Battery replacement
indicator
Page 4
POWERFUL
button
Page 7
N
AME OF EACH PART
Before operation:
Insert the power supply plug into the power outlet and/or
turn the breaker on.
Installing the remote controller batteries
P
REPARATION BEFORE OPERATION
1.
Remove the front lid.
2.
Insert the negative
pole of AAA alkaline
batteries fi rst.
3.
Install the front lid.
4.
Press RESET.
Setting current time
1.
Press CLOCK.
4.
Press CLOCK again.
2.
Press either the TIME button
or the TIMER buttons to set
the time.
Each press increases/de-
creases the time by 1 minute
(10 minutes when pressed
longer).
3.
Press the DAY button
to set the day.
Note:
• Press CLOCK gently using a thin instrument.
Note:
• Make sure the polarity of the batteries is correct.
• Do not use manganese batteries and leaking batteries. The remote controller
could malfunction.
• Do not use rechargeable batteries.
• The battery replacement indicator lights up when the battery is running low.
In about 7 days after the indicator starts lights up, the remote controller stops
working.
• Replace all batteries with new ones of the same type.
• Batteries can be used for approximately 1 year. However, batteries with ex-
pired shelf lives last shorter.
• Press RESET gently using a thin instrument. If the RESET button is not
pressed, the remote controller may not operate correctly.
<only GW50/60/71/80>
Note:
How to set remote controller exclusively for a particular indoor unit
A maximum of 4 indoor units with wireless remote controllers can be used in
a room.
To operate the indoor units individually with each remote controller, assign a
number to each remote controller according to the number of the indoor unit.
This setting can be set only when all the following conditions are met:
• The remote controller is powered OFF.
(1) Hold down button on the remote controller for 2 seconds to enter the
pairing mode.
(2) Press button again and assign a number to each remote controller.
Each press of button advances the number in the following order: 1 →
2 → 3 → 4.
(3) Press button to complete the pairing setting.
After you turn the breaker ON, the remote controller that fi rst sends a signal
to an indoor unit will be regarded as the remote controller for the indoor unit.
Once they are set, the indoor unit will only receive the signal from the as-
signed remote controller afterwards.
DG79A01WH01_en.indd 4 2022/02/18 17:17:49