manualshive.com logo in svg

Mitsubishi Electric MS-GE50VB-E1, Service Manual, Page: 33 / 36

Share
Download
Mitsubishi Electric MS-GE50VB-E1 Service Manual Download Page 33

33

DISASSEMBLY INSTRUCTIONS

11

(1)  Slide the sleeve and check if there is a locking lever or not.

(2)  The terminal with this connector has the locking
      mechanism.

   Slide the sleeve.
   Pull the terminal while 
   pushing the locking
   lever.

   Hold the sleeve, and 
   pull out the terminal 
   slowly.

The terminal which has the locking mechanism can be detached as shown below.
There are two types ( Refer to (1) and (2)) of the terminal with locking mechanism.
The terminal without locking mechanism can be detached by pulling it out.
Check the shape of the terminal before detaching.

<"Terminal with locking mechanism" Detaching points>

Connector

Sleeve

Locking lever

11-1. MSC-GE20VB  MSC-GE25VB  MSC-GE35VB 

NOTE: 

Turn OFF power supply before disassembly.

OPERATING PROCEDURE

PHOTOS

1. Removing the front panel

(1) Remove the screw caps of the front panel.
     Remove the screws.
(2) Pull the panel down to your side slightly and unhook the 

catches at the top.

2. Removing the electronic control P.C. board and the 

power monitor, receiver P.C. board

NOTE

 

:

 In case of removing only indoor electronic control        

 

P.C. board, work (3) is not necessary.

(1) Remove the front panel. (Refer to 1.)
(2) Remove the power monitor, receiver P.C. board holder 

from the bottom of electrical box.

(3) Open the power monitor, receiver P.C. board holder and 

remove the power monitor, receiver P.C. board.

(4) Remove the screw of the electrical cover and the electrical 

cover.

(5) Remove the screw of the V.A. clamp and the V.A. clamp.
(6) Remove the screw of the cord clamp and the cord clamp.
(7) Remove the screw of the terminal block.
(8) Remove the screw of the earth wire.
(9) Pull out indoor electronic control P.C. board slightly.
(10) Disconnect all the connectors on the electronic control P.C. 

board.

(11) Remove the electronic control P.C. board and the power 

monitor, receiver P.C. board.

Photo 2

Photo 1

Terminal block
fixing screw

Screw of the V.A.
clamp

Indoor electronic 
control P.C. board

Screws of the front panel

Screw of the
earth wire

Power monitor, receiver 
P.C. board holder 

Screw of the

electrical cover 

Cord clamp fixing
screw

OBH529A

Summary of Contents for MS-GE50VB-E1





































Reviews:

No comments