manualshive.com logo in svg

Mitsubishi Electric MR-J5 Series, User Manual

The Mitsubishi Electric MR-J5 Series is a cutting-edge product designed for precision and efficiency. Enhance your understanding and operation of this advanced technology with our comprehensive User Manual, available for free download at manualshive.com. This manual offers detailed instructions and insightful tips to maximize the potential of your MR-J5 Series.

Share
Download
background image

166

6  OPTIONS AND PERIPHERAL EQUIPMENT
6.8  Selection example of wires

6.8

Selection example of wires

To comply with the IEC/EN/UL/CSA standard, use the wires indicated below. To comply with other standards, 
use wire that complies with each standard.

MR-J5-G/MR-J5W-G User's Manual (Introduction)

MR-J5-A User's Manual (Introduction)

Refer to the following for a selection example of when the MR-J5 servo amplifier is used with the DC power 
supply input.

Page 26 Using servo amplifier with DC power supply input

Selection conditions of wire size are as follows.
Construction condition: Single wire set in midair
Wiring length: 30 m or shorter

The following shows the wires used for wiring. Use the wires given in this section or equivalent wires.

N

-

C

P

+

L1

L2

L3

L11

L21

U

V

W

M

1) Main circuit power supply lead

Servo amplifier

Power supply

2) Control circuit 

power supply lead

4) Servo motor power lead 

5) Power regeneration converter lead

Power regeneration 
converter

Regenerative option

3) Regenerative option lead

Summary of Contents for MR-J5 Series





























































































































































































































































































































Reviews:

No comments

Related manuals for MR-J5 Series

Randall X2 Owner'S Manual preview
X2
Brand: Randall Pages: 9
NAD 310 Owner'S Manual preview
310
Brand: NAD Pages: 32
Yamaha MX-1 Owner'S Manual preview
MX-1
Brand: Yamaha Pages: 8
lag STUDIOLAG PLUS User Manual preview
STUDIOLAG PLUS
Brand: lag Pages: 2
Calearo CPA-Cellular User Manual preview
CPA-Cellular
Brand: Calearo Pages: 23
Texas Instruments LM3886 Overture Manual preview
LM3886 Overture
Brand: Texas Instruments Pages: 24
Absolute Measurement L-ANV-0-0-R-AC Instruction Manual preview
L-ANV-0-0-R-AC
Brand: Absolute Measurement Pages: 10
IMG STAGE LINE STA-300D Instruction Manual preview
STA-300D
Brand: IMG STAGE LINE Pages: 20
Crown CTs 2000 Specifications preview
CTs 2000
Brand: Crown Pages: 1
CPI Satcom Division VZC-6967 Series Installation, Operation And Maintenance Manual preview
Satcom Division VZC-6967 Series
Brand: CPI Pages: 140
SilverStone ENSEMBLE EB03 Manual preview
ENSEMBLE EB03
Brand: SilverStone Pages: 8
zapco Z-PS Series Owner'S Manual preview
Z-PS Series
Brand: zapco Pages: 7
PowerBass XTA 4000D Owner'S Manual preview
XTA 4000D
Brand: PowerBass Pages: 28
Rane MA 4 Operator'S Manual preview
MA 4
Brand: Rane Pages: 4
Polytron HV 36122 F Operating Manual preview
HV 36122 F
Brand: Polytron Pages: 12
Accustic Arts MONO III MK2 Manual preview
MONO III MK2
Brand: Accustic Arts Pages: 13
Geemarc AMPLICALL 10 Installation Manual preview
AMPLICALL 10
Brand: Geemarc Pages: 11
iSP Technologies THETA Owner'S Manual preview
THETA
Brand: iSP Technologies Pages: 12

Brands by name

Popular brands

Load more brands