manualshive.com logo in svg

Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series, User Manual

Share
Download
Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series User Manual Download Page 104

102

7  ABSOLUTE POSITION DETECTION SYSTEM
7.1  Outline

Servo parameter setting

Set [Pr. PA03 Absolute position detection system] to "1" (enabled (absolute position detection system)).

Homing

After the absolute position detection system is enabled, [AL. 025 Absolute position erased] occurs at the initial startup. Then, 
ABSV (Absolute position erased) turns on. Refer to "CONTROL MODE" in the following manual and perform homing.

MR-JET User's Manual (Function)

Checking the detected absolute position data

Absolute position data can be checked with MR Configurator2.
Choose "Monitor" and "ABS Data Display" to open the absolute position data display screen.

*1 Refer to the following for the system architecture.

Page 103 Connecting the battery backup type absolute position encoder

No.

Item

Screen operation

MR Configurator2

System 
architecture 

*1

(1)

Motor side pulse unit value

Acquires and displays values in the unit of the servo motor side pulses from the servo amplifier 
of the specified axis.

(2)

Command pulse unit value

Current 
position

Acquires and displays the command pulse unit value from the servo amplifier for the specified 
axis.

(3)

CYC

1X

Acquires and displays the position within one revolution in the unit of the servo motor side 
pulses from the servo amplifier of the specified axis.

(4)

ABS

LS

Acquires and displays the multi-revolution counter travel distance from the absolute home 
position from the servo amplifier of the specified axis.

(5)

CYC0

1XO

Acquires and displays the home position within one revolution in the unit of the servo motor 
side pulses from the servo amplifier of the specified axis.

(6)

ABS0

LSO

Acquires and displays the multi-revolution counter value of the absolute home position from 
the servo amplifier of the specified axis.

Summary of Contents for Melservo-Jet MR-JET G-N1 Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands