manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R-R00CPU, User Manual

The Mitsubishi Electric MELSEC iQ-R-R00CPU is a cutting-edge automation controller that delivers high-speed performance and reliability. Unlock the full potential of this powerful device by accessing the detailed User Manual, available for free download on our website. Explore the limitless possibilities of this product today!

Share
Download
background image

37  FUNCTIONS

37.5  Program Execution in Both Systems

651

37

Tracking transfer

 • Do not set global devices used in a program executed in both systems as a tracking transfer target. Due to tracking 

transfer, the standby system data is overwritten with that of the control system, and the standby system program may 
operate in an unintended way.

 • When using a label in a program executed in both systems, use a local label.
 • When using an FB in a program executed in both systems, use a local FB. If a global FB is used, a program execution 

result of the control system is transferred and written over a program execution result of the standby system, causing an 
unintended operation.

Restricted instructions

The following table lists the instructions that are restricted in a program executed in both systems.

Classification

Notation

Description

Calling a subroutine program

CALL(P)

These instructions may not normally operate if a subroutine with any of a rising 
instruction, falling instruction, or SCJ instruction in a program which is not set as a both 
systems execution program is called in the standby system.

Calling a subroutine program and turning the 
output off

FCALL(P)

Calling a subroutine program in the specified 
program file

ECALL(P)

Calling a subroutine program in the specified 
program file and turning the output off

EFCALL(P)

Calling a subroutine program with output off

XCALL

Program control instruction

PSTOP(P)

No operation is performed if these instructions are executed on a program which is not 
set as a both systems execution program in the standby system.

POFF(P)

PSCAN(P)

Redundant system instruction

SP.CONTSW

No operation is performed if this instruction is executed in the standby system.

PID control instruction (Inexact differential)

S(P).PIDINIT

The PID control instruction information of the control system is transferred and written 
over the PID control instruction information of the standby system. When these 
instructions are executed in the standby system, a stop error may occur.

S(P).PIDCONT

S(P).PIDSTOP

S(P).PIDRUN

S(P).PIDPRMW

PID control instruction (Exact differential)

PIDINIT(P)

PIDCONT(P)

PIDSTOP(P)

PIDRUN(P)

PIDPRMW(P)

Summary of Contents for MELSEC iQ-R-R00CPU





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R-R00CPU

Canarm MC Series Installation Manual preview
MC Series
Brand: Canarm Pages: 3
Abus FUMO50110 Quick Manual preview
FUMO50110
Brand: Abus Pages: 12
Idesco EPC Manual preview
EPC
Brand: Idesco Pages: 11
B meters IWM-LR4 Quick User Manual preview
IWM-LR4
Brand: B meters Pages: 2
QUAD 34 Instruction Book preview
34
Brand: QUAD Pages: 17
fadini VIGILO 2250 Instruction Manual preview
VIGILO 2250
Brand: fadini Pages: 16
National Instruments PXIe-8238 Getting Started Manual preview
PXIe-8238
Brand: National Instruments Pages: 6
National Instruments PXI-8231 Installation Manual preview
PXI-8231
Brand: National Instruments Pages: 6
HQ Power VDPLC010 User Manual preview
VDPLC010
Brand: HQ Power Pages: 23
BABYTREND Expedition Double Jogger Instruction Manual preview
Expedition Double Jogger
Brand: BABYTREND Pages: 18
GEM 343 eSyDrive Operating Instructions Manual preview
343 eSyDrive
Brand: GEM Pages: 31
ICP DAS USA ECAT-2061 Quick Start preview
ECAT-2061
Brand: ICP DAS USA Pages: 4
ProSoft Technology InRAX MVI46-PDPS Manual preview
InRAX MVI46-PDPS
Brand: ProSoft Technology Pages: 72
Roland R1000 series E20 Manual preview
R1000 series E20
Brand: Roland Pages: 156
Bandini Industrie AS05080 Instructions For Installations preview
AS05080
Brand: Bandini Industrie Pages: 42
ccei MPZ Technical Instructions preview
MPZ
Brand: ccei Pages: 16
Astrosyn P542 User Manual preview
P542
Brand: Astrosyn Pages: 7
Morningstar SUNSAVER SS-10-12V Installation And Operation Manual preview
SUNSAVER SS-10-12V
Brand: Morningstar Pages: 26

Brands by name

Popular brands

Load more brands