manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN, User Manual

Share
Download
Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 55

1  FUNCTIONS

1.2  Transient Transmission

53

1

Communications using the engineering tool

This type of communications are used to configure the settings of or monitor each station using the engineering tool.
It allows seamless communications with stations on different types networks.

Communications can be made with stations up to eight networks apart (number of relay stations: 7).

When the networks consist of only MELSEC iQ-R series

Communication paths are automatically set for communications with the following networks of MELSEC iQ-R series.
 • Ethernet
 • CC-Link IE TSN
 • CC-Link IE Controller Network
 • CC-Link IE Field Network

■

Setting method

Check that "Dynamic Routing" in "Application Settings" is set to "Enable".

 • Communication paths are automatically set, but they can also be manually set. (

 Page 53 When the 

networks consist of MELSEC iQ-R series and other series)

 • The communication path cannot be set automatically for Ethernet-equipped modules connected via a 

router. Set the communication path manually. (

 Page 53 When the networks consist of MELSEC iQ-R 

series and other series)

When the networks consist of MELSEC iQ-R series and other series

Setting communication paths allow communications with the following networks configured with modules other than MELSEC 
iQ-R series.
 • Ethernet
 • CC-Link IE Controller Network
 • CC-Link IE Field Network
 • MELSECNET/H
 • MELSECNET/10

■

Setting method

Set communication paths in "Routing Setting" of "CPU Parameter". (

 MELSEC iQ-R CPU Module User's Manual 

(Application))

(Relay station)

(Relay station)

Ethernet

Ethernet

Engineering tool

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands