Mitsubishi Electric MELSEC iQ-R CC-Link IE TSN User Manual Download Page 205 | Manualshive

Page: 205 / 330

background image

4 TROUBLESHOOTING

4.5 List of Error Codes

203

4

4.5

List of Error Codes

This section lists the error codes, error definitions and causes, and actions for the errors that occur in the processing for data
communication between the RJ71GN11-T2 and external devices or occur by processing requests from the CPU module on
the own station.
Error codes are displayed in the [Error Information] tab in the "Module Diagnostics" window of the RJ71GN11-T2. (



166 Error Information)

Error
code

Error definition and causes

Action

Detailed
information 1

Detailed
information 2

1080H

The number of writes to the flash ROM has
exceeded 100000.

Replace the module.



1124H

• The default gateway is not set correctly.
• The gateway IP address is not set

correctly.

• The default gateway/gateway IP address

(network address after the subnet mask) is
different from that of the IP address of the
own node.

• Correct the default gateway IP address.
• Set the same network address as that of the IP address.

■

Parameter

information

• Parameter type
• I/O No.
• Parameter No.
• Network No.
• Station No.

■



1128H

The port number is incorrect.

Correct the port number.



1152H

The IP address is not set correctly.

Correct the IP addresses.

■

Parameter

information

• Parameter type
• I/O No.
• Parameter No.
• Network No.
• Station No.

■



1155H

• The specified connection was already

closed in TCP/IP communications.

• Open processing is not performed.

• Perform the open processing for the specified connection.
• Check if the open processing has been performed in the external device.



1167H

Unsent data found, but could not be sent.

• Check the settings for connection with the external device.
• Check the operation of the external device or switching hub.
• Since there may be congestion of packets on the line, send data after a

certain period of time.

• Check if the Ethernet cable is connected properly.
• Check that there is no connection failure with the switching hub.
• Execute the communication test, and if the test was completed with an

error, take corrective action.



«
...
203
204
205
206
207
...
»

Summary of Contents for MELSEC iQ-R CC-Link IE TSN











































































































































































































































































































































Reviews:

No comments

Related manuals for MELSEC iQ-R CC-Link IE TSN

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: Bartlett Pages: 30

Brand: Dantherm Pages: 96

Brand: FAAC Pages: 32

SHERPA MONOBLOC B0812

Brand: Olimpia splendid Pages: 44

Brand: Olimpia splendid Pages: 44

Brand: Olimpia splendid Pages: 16

Cutler-Hammer LMR

Brand: Eaton Pages: 38

Brand: Hiwin Pages: 99

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Quickie Pages: 64

Brand: Kamstrup Pages: 7

Brand: Bettis Pages: 18

Brand: EisSound Pages: 10

MURPHYMATIC ASM160

Brand: Murphy Pages: 4

Brand: Nice Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands