Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 53

Page: 53 / 96

7 PARAMETER SETTINGS

7.1 Parameter Setting Procedure

PARAMETER SETTINGS

This chapter describes the parameter setting required for the FX5-ASL-M.

7.1

Parameter Setting Procedure

Add the FX5-ASL-M to GX Works3.

[Navigation window]



[Parameter]



[Module Information]



Right click



[Add New Module]

The parameter setting includes a basic setting and refresh setting. Select the settings in the tree and set the items in the
following window.

[Navigation window]



[Parameter]



[Module Information]



[FX5-ASL-M]



[Module Parameter]

Write the setting to the CPU module with GX Works3.

[Online]



[Write to PLC]

Reset the CPU module or power off and on the system to apply the setting.

7.2

Basic Setting

Set the number of transmission points of the FX5-ASL-M and others.

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Related manuals for MELSEC iQ-F FX55-ASL-M

Brands by name

Popular brands