Mitsubishi Electric MELSEC iQ-F FX55-ASL-M User Manual Download Page 18

Page: 18 / 96

2 SPECIFICATIONS
2.1 General Specifications

SPECIFICATIONS

This chapter describes the FX5-ASL-M specifications.

2.1

General Specifications

The items other than the following are equivalent to those of the CPU module.
For the general specification, refer to the following manual.



MELSEC iQ-F FX5U User's Manual (Hardware)



MELSEC iQ-F FX5UC User's Manual (Hardware)

2.2

Power Supply Specifications

The following table lists the power supply specifications.

*1 Refer to the following for information about the relationship among the total length, the wire diameter of transmission cables (DP, DN),

and the transmission cable supply current.
On some slave modules with cables, the wire diameter of module-integrated transmission cables (DP, DN) may be smaller than 0.75



However, they can be used without any problem, provided that the wire diameter of transmission cables (DP, DN) meets the following
requirements.

Items

Specifications

Dielectric withstand voltage

500 V AC for 1 minute

Between all terminals and ground terminal

Insulation resistance

10 M



or higher by 500 V DC

insulation resistance tester

Items

Specifications

External power supply

Power supply voltage

24 V DC +15%, -10%, ripple voltage 0.5 Vp-p or lower
Recommended voltage: 26.4 V DC (24 V DC +10%)
Please use a UL Class 2 power supply

Current consumption

100 mA

Transmission cable
supply current

MAX 2 A

Internal power supply

Power supply voltage

5 V DC

Current consumption

200 mA

Wire diameter of transmission
cables (DP, DN)

Transmission cable supply current

Total length of 50 m or less

Total length of 50 to 100 m

Total length of 100 to 200 m

1.25



2 A maximum

1 A maximum

0.5 A maximum

0.75



1.2 A maximum

0.6 A maximum

0.3 A maximum

Summary of Contents for MELSEC iQ-F FX55-ASL-M

































































































Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Brands by name

Popular brands

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, User Manual

Search results

Summary of Contents for MELSEC iQ-F FX55-ASL-M

Reviews:

Brands by name

Popular brands