Mitsubishi Electric Lossnay LGH-150RVXT-E, Installation Instructions Manual

Page: 21 / 25

Eng-20
1R
Operation monitor output synchronized
with exhaust fan or supply fan
Set operation monitor output from TM3
90
V\QFKURQL]HGZLWK
supply of exhaust fan.
$OVRVXSSO\IDQGHOD\RSHUDWLRQH[IRUDIWHUKHDWHUFDQEHVHW
DIP-SW
Setting
check
3='5(
Setting
check
Operation monitor
output from TM3
90
SW No. Setting Function No. Setting Data
6:
SW5-2
- -
0
)DFWRU\VHWWLQJ
DIP-SW priority
2))
5-2 OFF
)DFWRU\VHWWLQJ
1 EA fan monitor output
2))
5-2 ON
2
SA fan monitor output
* When supply fan stops
during cold outdoor temp.
RUGHIURVWLQJRXWSXWVWRSV
21
(Either
5-2 ON or
2))
3
Operation monitor output
corresponds with supply
fan with following.
Starts the output 10 seconds
after supply fan operates.
Fan continues to operate
supply fan for 3 min after
stopping the output.
7RXVH6:DVWKHDIWHUKHDWHUREVHUYHWKHFDXWLRQVOLVWHGLQ
4 on
the page 11.
1R By-pass monitor output or Pre-heater
output setting
Set By-pass monitor or Pre-heater output from TM3
70
V\QFKURQL]HGZLWKVXSSO\RIH[KDXVWIDQ
DIP-SW
Setting
check
3='5(
Setting
check
Output setting from
TM3
70
SW No. Setting Function No. Setting Data
SW5-6
- -
0
)DFWRU\VHWWLQJ
DIP-SW priority
OFF
)DFWRU\VHWWLQJ
1
By-pass ventilation
operation monitor
output. Corresponds to
operation mode output
of By-pass damper.
ON 2
Pre-heater output.
Corresponds to operation
output supply fan with
following. Start the output
10 seconds after supply
fan starts. Fan continues
to operate for 3 min after
stopping the output. Lossnay
starts output when outdoor
WHPSÛ&RUOHVVDQGVWRSV
output when detecting temp.
EHFRPHVÛ&/RVVQD\VWRS
the output every 1 hour. Error
code is shown on the remote
controller and stop the output
in case of following.
7+GHWHFWVKLJKHUWKDQ
Û&ZLWKLQPLQXWHVDIWHU
the output starts.
7+GHWHFWVÛ&RU
ORZHUPLQXWHVDIWHUWKH
output starts.
)RUKHDWHUVHOHFWLRQREVHUYHWKHFDXWLRQVOLVWHGLQ
4 on the page
11.
- When set to auto ventilation mode while using the Pre-heater
IXQFWLRQWKHRXWGRRUWHPSHUDWXUHPD\EHGHWHFWHGDVKLJKHUDQG
WKHPRGHPD\FKDQJHWR%\SDVVPRGHHYHQLQZLQWHU
'XULQJSUHKHDWHULV21/RVVQD\GRHVQRWJRWR)DQVSHHG
(YHQUHPRWHFRQWUROOHUGLVSOD\V)DQVSHHG/RVVQD\LVRSHUDWHG
at Fan speed 2.
Function settings (continued)
No.59
Pre-heater output setting 1)
ON temperature
Set the outdoor temperature for Pre-heater output ON.
:KHQGHWHFWLQJWHPSEHFRPHVWKHVHWWLQJRUOHVV3UHKHDWHURXWSXW
from TM3
70
starts.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
3='5(
Setting
check
Outdoor temp. for Pre-
heater output ON
SW No. Setting Function No. Setting Data
N/A
- -
59
0
)DFWRU\VHWWLQJ
Û&RUOHVV
- - 1
Û&RUOHVV
- - 2
Û&RUOHVV
- - 3
Û&RUOHVV
- - 4
Û&RUOHVV
- - 5
Û&RUOHVV
- - 6
Û&RUOHVV
- -
Û&RUOHVV
No.60
Pre-heater output setting 2)
OFF interval
Set the Pre-heater output interval. Output stops according to the set
hours.
DIP-SW
Setting
check
3='5(
Setting
check
Pre-heater output OFF
interval
SW No. Setting Function No. Setting Data
N/A
- -
60
0
)DFWRU\VHWWLQJ
1 hr
- - 1 2 hrs
- - 2 3 hrs
- - 3 4 hrs
- - 4 5 hrs
No.61
Fan speed for air volume “High” input
6HWWKHIDQVSHHGVHWWLQJZKHQUHFLJK´VLJQDOIURPUHPRWH
FRQWUROOHUVHJUHPRWHFRQWUROOHURI&LW\0XOWLDQG0U6OLP/RVVQD\
VLPSOHUHPRWHFRQWUROOHUZKLJK/RZRU+LJK0LGGOH/RZ
air volume.
DIP-SW
Setting
check
3='5(
Setting
check
Operating fan speed
SW No. Setting Function No. Setting Data
SW2-9
- -
61
0
)DFWRU\VHWWLQJ
DIP-SW priority
OFF
)DFWRU\VHWWLQJ
1 Fan speed 4
ON 2 Fan speed 3
No.62
Fan speed for air volume “Low” input
Set the fan speed setting when receiving “Low” signal from remote
FRQWUROOHUVHJUHPRWHFRQWUROOHURI&LW\0XOWLDQG0U6OLP/RVVQD\
VLPSOHUHPRWHFRQWUROOHUZKLJK/RZ
DIP-SW
Setting
check
3='5(
Setting
check
Operating fan speed
SW No. Setting Function No. Setting Data
SW2-10
- -
62
0
)DFWRU\VHWWLQJ
DIP-SW priority
OFF
)DFWRU\VHWWLQJ
1 Fan speed 2
ON 2 Fan speed 1