Mitsubishi Electric FR-F700PJ Series Instruction Manual Download Page 25 | Manualshive

Page: 25 / 356

background image

12

Inverter placement (Installation of Filterpack)

1.5.2

Installation of the inverter and Filterpack (for rear panel installation)

NOTE



When encasing multiple inverters, install them in parallel as a cooling
measure.



Install the inverter vertically.



For heat dissipation and maintenance, allow minimum clearance shown
in the figures below from the inverter to the other devices and to the
inner surface of the enclosure.



Allow 5cm or more clearance for 5.5K or higher.



When using the inverters at the surrounding air temperature of 40



C or less, the inverters can be installed without any clearance between

them (0cm clearance).

<0.4K to 3.7K>

Remove the front cover and wiring cover to attach the inverter.

<5.5K to 15K>

Remove the L-bracket installation screws from Filterpack (two for the 7.5K or lower, three for the 11K or higher), and attach
the included L-bracket to Filterpack with these screws.
Remove the front cover to attach the inverter.

V

e

rtical

Refer to the clearance

shown on the left.

10cm or more

10cm or more

Measurement
position

Measurement
position

5cm

5cm

5cm

-10 C to +50 C
(non-freezing)

1cm or
more

∗1, ∗2

1cm or
more

∗1, ∗2

1cm or
more

∗1

FR-F720PJ-1.5K to 3.7K

FR-F720PJ-0.4K to 0.75K

FR-F740PJ-0.4K to 3.7K

Screw for inverter rear
panel installation

Screw for inverter rear
panel installation

Front cover

Front cover

Wiring cover

Wiring cover

Screw for inverter rear
panel installation

Screw for inverter rear
panel installation

L-bracket installation screw

Screw for inverter
rear panel installation

Rear panel installation L-bracket

Screw for inverter rear panel installation

«
...
23
24
25
26
27
...
»

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Related manuals for FR-F700PJ Series

Brand: ZCS Pages: 74

Brand: Linear Technology Pages: 6

Brand: nedis Pages: 48

BNI IOL-712-000-K023

Brand: Balluff Pages: 12

Brand: EBARA Pages: 34

Brand: Humandata Pages: 10

Brand: TA Pages: 32

Brand: Majella Pages: 6

UT-GC-DMX-DECOD-5CH

Brand: U Technology Pages: 10

Brand: RS Pages: 7

Q.VOLT-G2 HYB-4.6kW.1.1

Brand: Q CELLS Pages: 118

Brand: COMPANION Pages: 16

Brand: MG Pages: 38

Brand: RDZ Pages: 60

Brand: Gefen Pages: 14

Brand: Simco Pages: 98

Brand: Guardian Pages: 68

Brand: MyTek Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands