manualshive.com logo in svg

Mitsubishi Electric FR-F700PJ Series, Instruction Manual

The Mitsubishi Electric FR-F700PJ Series is an advanced industrial product designed to deliver exceptional performance and energy efficiency. To ensure seamless operation, it is important to have the Instruction Manual. Download the comprehensive manual for free from manualshive.com and unlock the full potential of your FR-F700PJ Series.

Share
Download
background image

118

Setting of acceleration/deceleration time and acceleration/ deceleration pattern

4.8.4

Acceleration/deceleration pattern (Pr. 29)

The above parameters can be set when 

Pr. 160 Extended function display selection

 

="0". 

(Refer to page 197)

You can set the acceleration/deceleration pattern suitable for application.

Parameter 

Number

Name

Initial Value

Setting Range

Description

29

Acceleration/deceleration 
pattern selection

0

0

Linear acceleration/ deceleration

1

S-pattern acceleration/deceleration A

2

S-pattern acceleration/deceleration B

(1) Linear acceleration/deceleration (

Pr. 29 

setting "0", initial value)

For the inverter operation, the output frequency is made to change linearly (linear

acceleration/deceleration) to prevent the motor and inverter from getting
excessive stress to reach the set frequency during acceleration, deceleration, etc.
when frequency changes. Linear acceleration/deceleration has a uniform
frequency/time slope.

(2) S-pattern acceleration/deceleration A (

Pr. 29 

= "1")

For machine tool spindle applications, etc.

Use this pattern when acceleration/deceleration is required in a short time to a
high-speed range higher than the base frequency.
In this acceleration/deceleration pattern, 

Pr. 3 Base frequency 

 (fb) is the inflection

point of the S pattern, and you can set the acceleration/deceleration time
appropriate for motor torque reduction in a constant-power operation range of
base frequency (fb) or higher.

Rated motor frequency under IPM motor control 

(Refer to page 86)

NOTE

For the acceleration/deceleration time of the S-pattern acceleration/deceleration A, set the time to reach 

Pr.3 Base

frequency

 (rated IPM motor frequency under IPM motor control

  (

Refer to page 86

)

) but not the time to reach 

Pr.20

Acceleration/deceleration reference frequency

.

(3) S-pattern acceleration/deceleration B (

Pr. 29 

= "2")

For prevention of load shifting in conveyor and other applications.

Since acceleration/deceleration is always made in an S shape from current
frequency (f2) to target frequency (f1), this function eases shock produced at
acceleration/deceleration and is effective for load collapse prevention, etc.

Parameters referred to

Pr. 3 Base frequency 

 

Refer to page 103

Pr. 7 Acceleration time, Pr. 8 Deceleration time, Pr. 20 Acceleration/deceleration reference frequency 

 

Refer to page 113

(Hz)

Time

Setting value "0"

[Linear acceleration/

deceleration]

Output frequency

fb

(Hz)

Setting value "1"

[S-pattern acceleration/

deceleration A]

Output frequency

Time

f1

(Hz)

(Hz)

f2

Set frequency

Output frequency

Time

Setting value "2"

[S-pattern acceleration/

deceleration B]

Summary of Contents for FR-F700PJ Series





































































































































































































































































































































































Reviews:

No comments

Related manuals for FR-F700PJ Series

Barco ImagePRO-4K Quick Start Manual preview
ImagePRO-4K
Brand: Barco Pages: 2
Z3 Technology HE4K-DCK-1X User Instructions preview
HE4K-DCK-1X
Brand: Z3 Technology Pages: 86
KATEK Steca coolcept 3 fleX Installation And Operating Instructions Manual preview
Steca coolcept 3 fleX
Brand: KATEK Pages: 40
Patton electronics 222N9 User Manual preview
222N9
Brand: Patton electronics Pages: 16
SAJ 8000m-2SR4GH User Manual preview
8000m-2SR4GH
Brand: SAJ Pages: 59
StarTech.com USB32DVCAPRO Instruction Manual preview
USB32DVCAPRO
Brand: StarTech.com Pages: 10
Encore ENXTV-DIT - User Manual preview
ENXTV-DIT -
Brand: Encore Pages: 27
Lake People ADC F444 User Manual preview
ADC F444
Brand: Lake People Pages: 28
IBC SOLAR ServeMaster 1600MV User Manual preview
ServeMaster 1600MV
Brand: IBC SOLAR Pages: 58
Airpax Dimensions ADI-64/500 Owner'S Manual preview
ADI-64/500
Brand: Airpax Dimensions Pages: 6
Raleigh Audio RAKK DAC Mark II Installation Manual preview
RAKK DAC Mark II
Brand: Raleigh Audio Pages: 9
nedis 5412810327454 Quick Start Manual preview
5412810327454
Brand: nedis Pages: 52
Xantrex 1200, 1750 Owner'S Manual preview
1200, 1750
Brand: Xantrex Pages: 80
Hagstrom KEUSB24 User Manual preview
KEUSB24
Brand: Hagstrom Pages: 24
GefenTV GTV-192KUSB-2-ADAUD User Manual preview
GTV-192KUSB-2-ADAUD
Brand: GefenTV Pages: 36
Radial Engineering 9000-0033-6922 User Manual preview
9000-0033-6922
Brand: Radial Engineering Pages: 11
Microsens GE-C301 User Manual preview
GE-C301
Brand: Microsens Pages: 2
LEAB Clayton Power 1012 User Manual preview
Clayton Power 1012
Brand: LEAB Pages: 20

Brands by name

Popular brands

Load more brands