Mitsubishi Electric FR-A8ND Instruction Manual Download Page 9

Page: 9 / 104

PRE-OPERATION INSTRUCTIONS

NOTE

• Set the compatible mode switch before switching ON the inverter and do not change the setting while the power is

ON. Otherwise you may get an electric shock.

• Do not turn ON the switch 2 of the compatible mode switch.

1.3 MNS LED (operation status indication)

The MNS LED indicates the operating status of the option unit by its indication status.
Check the position of LED on

page 7

LED

indicator

Description

Corrective action

OFF

Inverter power OFF

Supply power to the inverter.

Network power OFF

Supply power to the network.

Cable disconnected

Check for a DeviceNet cable disconnection, connector contact fault, and misplaced
terminating resistor.

Own node only on the network

Supply power to the master.

Different baud rate between the
inverter and master

Set the same baud rate for the inverter (

Pr.346

) and master.

Green
(flickering)

Connection not established
(Cable connection and network
power are normal.)

Check the node address setting (node address switches and

Pr.345

) of the inverter.

Set the master to the RUN mode.

Check that the size (number of bytes) of the I/O communication from the master matches
with that set in

Pr.346

of the inverter. (For how to check the I/O communication size of the

master, refer to the Instruction Manual of the master device.)

Summary of Contents for FR-A8ND









































































































Search results

Summary of Contents for FR-A8ND

Reviews:

Related manuals for FR-A8ND

Brands by name

Popular brands

Mitsubishi Electric FR-A8ND, Instruction Manual

Search results

Summary of Contents for FR-A8ND

Reviews:

Related manuals for FR-A8ND

Brands by name

Popular brands