Mitsubishi Electric FR-A820-00046 (0.4K), Instruction Manual

Page: 958 / 1218

CC-Link IE Field Network (FR-A800-GF) Parameters
5 - 756
Remote register (from the inverter to the master module)
Device No. Signal Description
RWr0 Reply code
When "1" is set in RY21 or RY22, the following reply codes are set for the frequency
setting command. The setting value "0" is set normally, and a value other than "0" is
set at an error.
H0000: Normal
H0001: Write mode fault
H0003: Setting range fault
RWr2 Reply code
When "1" is set in RY23 or RY24, the following reply codes are set for the torque
command / torque limit. The setting value "0" is set normally, and a value other than
"0" is set at an error.
H0000: Normal
H0003: Setting range fault
RWr4,
RWr5,
RWr6
Reply code
When the PID command (RWw4 to RWw6) is set, the following reply code is set for the
PID command. The setting value "0" is set normally, and a value other than "0" is set at
an error.
H0000: Normal
H0003: Setting range fault
RWr10,
RWr12,
RWr14,
RWr16,
RWr18,
RWr1A
Reply code
When "1" is set in RY25, the following reply codes corresponding to the instruction
code RWw10, 12, 14, 16, 18, and 1A are set. The setting value "0" is set normally, and a
value other than "0" is set at an error.
H0000: Normal
H0001: Write mode fault
H0002: Parameter selection fault
H0003: Setting range fault
RWr11,
RWr13,
RWr15,
RWr17,
RWr19,
RWr1B
Read data
For a normal reply, the reply data to the instruction specified by the instruction code
is set.
RWr20 Error status
The setting value "0" is set during normal inverter operation, and the data code of the
corresponding error is set at an error. (For the data codes or details of fault records,
refer to page 6-5.)
RWr21 Fault record (fault data)
The data code of faults history No. specified by RWw21 is stored in the lower 8bits.
Lower 8 bits of RWw21 will be reverted back to the upper 8 bits.
RWr22 Fault record (output frequency) Output frequency of the faults history No. specified in RWw21 is stored.
RWr23 Fault record (output current) Output current of the faults history No. specified in RWw21 is stored.
RWr24 Fault record (output voltage) Output voltage of the faults history No. specified in RWw21 is stored.
RWr25 Fault record (energization time) Energization time of the faults history No. specified in RWw21 is stored.
RWr26 First monitor value
When "1" is set in RY20, the monitored data specified by the monitor code RWw26 to
RWw2F is saved.
Output frequency, output current, and output voltage monitors are held at an
inverter failure.
RWr27 Second monitor value
RWr28 Third monitor value
RWr29 Fourth monitor value
RWr2A Fifth monitor value
RWr2B Sixth monitor value
RWr2C Seventh monitor value
RWr2D Eighth monitor value
RWr2E Ninth monitor value
RWr2F Tenth monitor value
RWr30 to
RWr7F
Monitor value
Fixed monitored data are saved regardless of the RY20 setting.
Output frequency, output current, and output voltage monitors are held at an
inverter failure.
Tab. 5-349: Remote register (inverter master module)