Mitsubishi Electric FR-A7NCA Instruction Manual Download Page 29 | Manualshive

Page: 29 / 141

background image

21

INVERTER SETTING

4

4.4

Operation and Speed Command Source (Pr. 338, Pr. 339, Pr. 550)

(1) Select control source for the network operation mode

(Pr. 550)

A control location for the network operation mode can be selected from either the inverter RS-485
terminal or communication option.
When using a communication option, set "0 or 9999 (initial value)" in

Pr. 550

.

Refer to the inverter manual (applied) for details.

Parameter

Number

Name

Initial Value

Setting

Range

Description

550

NET mode operation
command source selection

9999

0

Control source of the communication
option is valid
(control source of the inverter RS-485
terminal is invalid)

1

Control source of the inverter RS-485
terminal is valid
(control source of the communication
option is invalid)

9999

Automatic recognition of the
communication option
Normally, control source of the RS-
485 terminal is valid. When a
communication option is mounted,
the control source of the
communication option is valid.

A7NCA.book 21 ページ２００６年７月３日　月曜日　午前９時４８分

«
...
27
28
29
30
31
...
»

Summary of Contents for FR-A7NCA














































































































































Reviews:

No comments

Related manuals for FR-A7NCA

Brand: Tabor Pages: 111

Brand: Q Acoustics Pages: 7

Brand: TAD Pages: 128

Brand: YASKAWA Pages: 128

Brand: µ-Dimension Pages: 6

Brand: Aksa Pages: 50

Brand: DK-Technologies Pages: 90

MaitreView 4KLite

Brand: AVLink Pages: 10

Brand: Parker Pages: 149

Brand: B&B Electronics Pages: 3

Brand: Badger Meter Pages: 12

EZWALL-pro 3x3 v3

Brand: SmartAVI Pages: 14

Brand: M-Audio Pages: 48

Brand: B&B Electronics Pages: 15

Brand: AceWav Pages: 2

Giga-MiniMC 856-10730-RX

Brand: B&B Electronics Pages: 15

Brand: ENC Pages: 57

Brand: NANO MACHINES Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands