Mitsubishi Electric EHWT17D-MHEDW Installation Manual Download Page 58

Issued
UNITED KINGDOM

Atsushi EDAYOSHI
Manager, Quality Assurance Department

1. Apr. 2022

MITSUBISHI ELECTRIC AIR CONDITIONING SYSTEMS EUROPE LTD.

NETTLEHILL ROAD, HOUSTOUN INDUSTRIAL ESTATE, LIVINGSTON, EH54 5EQ, SCOTLAND, UNITED KINGDOM

hereby declares under its sole responsibility that the air conditioner(s) and heat pump(s) for use in residential, commercial, and light-industrial environments described below:

intygar härmed att luftkonditioneringarna och värmepumparna som beskrivs nedan för användning i bostäder, kommersiella miljöer och lätta industriella miljöer:

vakuuttaa täten yksinomaisella vastuullaan, että jäljempänä kuvatut asuinrakennuksiin, pienteollisuuskäyttöön ja kaupalliseen käyttöön tarkoitetut ilmastointilaitteet ja lämpöpumput:

erklærer et fullstendig ansvar for undernevnte klimaanlegg og varmepumper ved bruk i boliger, samt kommersielle og lettindustrielle miljøer:

erklærer hermed under eneansvar, at det/de herunder beskrevne airconditionanlæg og varmepumpe(r) til brug i beboelses- og erhvervsmiljøer samt i miljøer med let industri:

kinnitab oma ainuvastutusel, et allpool toodud elu-, äri- ja kergtööstuskeskkondades kasutamiseks mõeldud kliimaseadmed ja soojuspumbad:

ar šo, vienpersoniski uzņemoties atbildību, paziņo, ka tālāk aprakstītais(-ītie) gaisa kondicionētājs(-i) un siltumsūknis(-i) ir paredzēti lietošanai dzīvojamajās, komercdarbības un vieglās rūpniecības tel

-

pās, kas aprakstītas tālāk:

šiuo vien tik savo atsakomybe pareiškia, kad toliau apibūdintas (-i) oro kondicionierius (-iai) ir šilumos siurblys (-iai), skirtas (-i) naudoti toliau apibūdintose gyvenamosiose, komercinėse ir lengvosios 

pramonės aplinkose:

erklärt hiermit auf seine alleinige Verantwortung, dass die Klimaanlage(n) und Wärmepumpe(n) für das häusliche, kommerzielle und leichtindustrielle Umfeld wie unten beschrieben:

verklaart hierbij onder eigen verantwoordelijkheid dat de voor huishoudelijke, handels- en lichtindustriële omgevingen bestemde airconditioner(s) en warmtepomp(en) zoals onderstaand beschreven:

déclare par la présente et sous sa propre responsabilité que le(s) climatiseur(s) et la/les pompe(s) à chaleur destinés à un usage dans des environnements résidentiels, commerciaux et d’industrie 

légère décrits ci-dessous :

niniejszym oświadcza na swoją wyłączną odpowiedzialność, że klimatyzatory i pompy ciepła do zastosowań w środowisku mieszkalnym, handlowym i lekko uprzemysłowionym opisane poniżej:

tímto na vlastní odpovědnost prohlašuje, že níže popsané klimatizační jednotky a tepelná čerpadla pro použití v obytných prostředích, komerčních prostředích a prostředích lehkého průmyslu:

MITSUBISHI ELECTRIC, EHWT17D-MHEDW

2014/35/EU: Low Voltage

2006/42/EC: Machinery

2014/30/EU: Electromagnetic Compatibility

2009/125/EC: Energy-related Products Directive and Regulation (EU) No 813/2013

2011/65/EU, (EU) 2015/863 and (EU) 2017/2102: RoHS Directive

EU DECLARATION OF CONFORMITY

EG-DEKLARATION OM ÖVERENSSTÄMMELSE

EU-VAATIMUSTENMUKAISUUSVAKUUTUS

EU-ERKLÆRING OM SAMSVAR

EU-OVERENSSTEMMELSESERKLÆRING

EL-I VASTAVUSDEKLARATSIOON

ES ATBILSTĪBAS DEKLARĀCIJA

ES ATITIKTIES DEKLARACIJA

EU-KONFORMITÄTSERKLÄRUNG

EU-CONFORMITEITSVERKLARING

DÉCLARATION DE CONFORMITÉ UE

DEKLARACJA ZGODNOŚCI UE

EU PROHLÁŠENÍ O SHODĚ

is/are in conformity with provisions of the following Union harmonisation legislation.

uppfyller villkoren i följande harmoniserade föreskrifter inom unionen.

ovat seuraavan unionin yhdenmukaistamislainsäädännön säännösten mukaisia.

er i samsvar med forskriftene til følgende EU-lovgivning om harmonisering.

er i overensstemmelse med bestemmelserne i følgende harmoniserede EU-lovgivning.

vastavad järgmiste Euroopa Liidu ühtlustatud õigusaktide sätetele.

atbilst šādiem ES harmonizētajiem tiesību aktu noteikumiem.

taip pat atitinka kitų toliau išvardytų suderintųjų Sąjungos direktyvų nuostatas.

die Bestimmungen der folgenden Harmonisierungsrechtsvorschriften der Union erfüllt/

erfüllen.

voldoet/voldoen aan bepalingen van de volgende harmonisatiewetgeving van de Unie.

est/sont conforme(s) aux dispositions de la législation d’harmonisation de l’Union sui-

vante.

są zgodne z przepisami następującego unijnego prawodawstwa harmonizacyjnego.

jsou v souladu s ustanoveními následujících harmonizačních právních předpisů Unie.

RK79D203K01_01en.indd   56

2022/02/14   16:52:59

058

Summary of Contents for EHWT17D-MHEDW





























































Reviews: