manualshive.com logo in svg

Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8, User Manual, Page: 71 / 162

Share
Download
Mitsubishi Electric CC-Link IE Field NZ2GF12A-60IOLH8 User Manual Download Page 71

7  FUNCTIONS

7.1  IO-Link Master Functions

69

7

IO-Link device validation function

This function validates compatibility and identity of the IO-Link device connected to each channel.
This function can be used to recognize connection with unintended IO-Link devices when replacing IO-Link devices.
Check that the connected IO-Link device is an intended one, and review the connection or disable the IO-Link device 
validation setting to validate the IO-Link device after replacement.
The CQ LED indicates the result of IO-Link device validation. (

 Page 117 Checking the LEDs)

Description

The following table lists validation types and items to be validated.

For this function, set the validation type for each channel on the parameter setting window of the engineering tool or via a 
program.
For confirmation of data to be read/written in transient communication (access code: 21H), set the validation type to either of 
the above to validate the device.
To apply changes of settings made in processing other than the initial processing and parameter setting on an engineering 
tool, turn on Operation condition setting request flag (RWw0.b9).
For details on setting parameters via a program, refer to the following.

Page 87 Device validation

To use the IO-Link device validation function with "Initial operation setting" being set to "Without initial 
processing", set "Initial operation setting" to "Without initial processing" again after the device validation 
setting.
If not, the correct value is not stored.
For details on the initial operation setting, refer to the following.

Page 80 Initial Operation Setting Function

Page 84 Initial operation setting

Preparation

When performing compatibility validation and identity validation, confirm the vendor ID, device ID, and serial number of the IO-
Link device.
The following describes the procedure for confirming the vendor ID, device ID, and serial number of the IO-Link device.

1.

Display the "Command Execution of Slave Station" window.

From the list of stations, select an IO-Link module 

 [CC IE Field Configuration] 

 [Online] 

 [Command Execution of 

Slave Station].

: Validated, 

: Not validated

Validation type

Validated item

Vendor ID

IO-Link device ID

Serial number

Disabled

Compatible

Identical

Summary of Contents for CC-Link IE Field NZ2GF12A-60IOLH8



































































































































































Reviews:

No comments