manualshive.com logo in svg

Mitsubishi Electric AnyWire ASLINK, User Manual, Page: 17 / 200

Share
Download
Mitsubishi Electric AnyWire ASLINK User Manual Download Page 17

2  SPECIFICATIONS

2.1  General Specifications

15

2

2

SPECIFICATIONS

2.1

General Specifications

The following table lists the general specifications.

*1 Do not use or store the programmable controller under pressure higher than the atmospheric pressure of altitude 0m.

Doing so may cause malfunction.
When using the programmable controller under pressure, please consult your local Mitsubishi representative.

*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power 

distribution network and the machinery within premises.
Category 

 applies to equipment for which electrical power is supplied from fixed facilities.

The surge voltage withstand level for the equipment with the rated voltage of 300V or less is 2500V.

*3 This index indicates the degree to which conductive material is generated in terms of the environment in which the equipment is used.

In pollution degree 2, only non-conductive pollution occurs. A temporary conductivity caused by an accidental condensation may also 
occur occasionally.

*4 The equipment can also be used outside the control panel, provided that environmental conditions such as operating ambient 

temperature and operating ambient humidity are met.

Item

Specifications

Operating ambient 
temperature

0 to 55

Storage ambient 
temperature

-25 to 75

Operating ambient 
humidity

5 to 95%RH, non-condensing

Storage ambient 
humidity

Vibration resistance

Compliant with IEC 
61131-2 and JIS B 
3502

Frequency

Constant 
acceleration

Half amplitude

Number of sweeps

Under intermittent 
vibration

5 to 8.4Hz

3.5mm

10 times each in X, 
Y, and Z directions

8.4 to 150Hz

9.8m/

Under continuous 
vibration

5 to 8.4Hz

1.75mm

8.4 to 150Hz

4.9m/

Shock resistance

Compliant with IEC 61131-2 and JIS B 3502 (147m/

, 3 times each in X, Y, and Z directions)

Operating 
atmosphere

No corrosive gas

Operating altitude

*1

0 to 2000m

Installation location

Inside a control panel

*4

Overvoltage 
category

*2

 or less

Pollution degree

*3

2 or less

Equipment class

Class 

Summary of Contents for AnyWire ASLINK









































































































































































































Reviews:

No comments