General Notes on Programming
8350-383-113-BA
39
Draft 1A, September 1998
•
Master unit must not be allowed to exit the programming mode and no off-hook to
on-hook transitions can occur in any unit while the Cloning cable is connected between
units. These transitions can cause a CIL output that will confuse the units and possibly
corrupt the programming.
•
Slave unit must be powered down and then powered up after Cloning. The Cloning cable
must be disconnected prior to powering up the Slave unit.
6. 12. 3. Steps for Cloning
The following steps must be completed before attempting to Clone:
•
pre-program and dedicate a Master unit
•
connect an MF4 device to the Master unit that can seize the line, generate MF4 tones and
listen for the acknowledgment tones
•
you must have an Exchange line/trunk or a simulated source connected to the line you are
using on the Master EuroRoute
•
ensure each EuroRoute is powered up and connected using the Cloning cable as illustrated
in Figure 6.13. The EuroRoute requires pins two, three and five to be configured as a null
modem cable (Figure 6.13).
Figure 6.13 Cloning Cable
6. 12. 4. Procedure
To Clone a EuroRoute:
1. ensure that the Slave unit has been initialised
2. power up the Master unit
3. verify that the desired programming is already resident in the Master EuroRoute
4. power up the Slave unit
5. match the Master and Slave baud rates (see register 000, Serial Port Baud Rate)
6. connect the Cloning cable and the MF4 device as illustrated in Figure 6.12
7. go off-hook on the MF4 device connected to the Master unit
8. dial the programming access code (#0
✳
by default)
9. dial 942 906 to start the Clone procedure
10. in approximately 5 to 10 seconds you should hear either two tones indicating that a
successful Cloning has taken place or four long tones indicating that the cloning attempt
failed. If four tones or no tones occur, verify the conditions in section 6.12.2
11. After a successful Cloning, disconnect the Cloning cable and power down the Slave unit
for 15 seconds. Do not attempt to make the Slave unit function while the Cloning cable is
connected. When powered-up the Slave unit will be functional, with its database a
duplicate of the Master unit
12. If more units are to be cloned, repeat steps 4 to 11.
CLONING CABLE
MASTER
SLAVE
2
3
5
MALE
MALE
5
3
2
Summary of Contents for SmarT-1 EuroRoute
