Mitel MiVOICE BUSINESS Engineering Manualline Download Page 249 | Manualshive

Page: 249 / 381

background image

Network Configuration Specifics

235

SOURCES THAT CAN BE USED TO OBTAIN NETWORK POLICY
INFORMATION

Table 67 indicates which LAN Policy parameters can be obtained from each of the different
sources of information.

NETWORK CONFIGURATION INFORMATION AND PRIORITIES

To obtain network configuration information such as IP addresses, L2 priority settings, L3 priority
settings and VLAN information the phones can be programmed manually or they can obtain
information via auto-discovery using LLDP-MED, CDP or DHCP mechanisms.

It is possible to program some network configuration information manually and obtain other
information via LLDP-MED, DHCP or CDP and also use default values.

The IP phone looks for VLAN setting information and network configuration information in a
specific priority order until all of the appropriate fields have been filled in. This priority order for
obtaining information is described in the following sections.

Table 67: Sources of Network Policy Information

SOURCE

OF INFO

PHONE IP

ADDRESS

DEFAULT

GATEWAY

IP

ADDRESS

SUBNET

MASK

VLAN

(802.1Q)

INFO

L2 QOS

PRIORITY

(802.1D/P)

L3

QOS

(DSCP)

RTC IP

ADDRESS

TFTP

SERVER IP

ADDRESS

DNS IP

ADDRESS

Manual
entry

Yes

Yes

Yes

Yes

Yes (0-6)

Yes

(0-63)

Yes

Yes

Yes

LLDP-MED

N/A

N/A

N/A

Yes

Yes (0-6)

Yes

(0-63)

N/A

N/A

N/A

CDP

N/A

N/A

N/A

Yes

See Note

2

N/A

N/A

N/A

N/A

DHCP

Yes

Yes

Yes

Yes, uses

double fetch

Yes (0-6)

Yes

(0-63)

Yes

Yes

Yes

Default
Values

N/A

N/A

N/A

No VLAN,

untagged

6 (If VLAN

via CDP

then

default is

5),

46

(Note)

N/A

N/A

N/A

Note 1

: A DSCP value of 46 is recommended for newer installations using DSCP-aware routers. Value 46 will place the voice

into the Expedited Forwarding Queue (EF).

Note 2

: Depending on certain network conditions the phone will use different DSCP default values. The default values under

specific conditions are:

• If the VLAN information was learnt via CDP, signalling will use a default DSCP value of ‘46’ and voice will use

a default DSCP value of ’46’. These values can be changed with additional programming.

• In situations where VLAN information cannot be learnt from either CDP or DHCP, the phone will use a DSCP

value of ‘0’ for both signalling and voice.

«
...
247
248
249
250
251
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: NEC Pages: 30

ElectraElite IPK

Brand: NEC Pages: 20

Brand: i-mobile Pages: 72

Brand: myPhone Pages: 39

Brand: Alcatel-Lucent Pages: 62

Brand: Kyocera Pages: 32

SCOPIA Elite 5200

Brand: RADVision Pages: 17

Brand: mPTech Pages: 50

Brand: cromax Pages: 9

8100 SMARTPHONE

Brand: Blackberry Pages: 230

Brand: Pantech Pages: 61

Brand: Alcatel Pages: 2

Brand: Icemobile Pages: 11

Brand: T-Mobile Pages: 59

Brand: BURY Pages: 25

Brand: Sharp Pages: 324

Brand: Lava Pages: 21

Anycall SGH-Z368

Brand: Samsung Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands