manualshive.com logo in svg

Mitel MiVOICE BUSINESS, Engineering Manualline

Download the free Quick Reference Manual for Mitel MiVOICE BUSINESS, the ultimate communication solution. This comprehensive manual provides step-by-step instructions, allowing users to easily navigate and maximize the features of this cutting-edge product. Get your manual from manualshive.com today.

Share
Download
background image

Power

113

UNINTERRUPTIBLE POWER SUPPLY (UPS)

Use uninterruptible power supplies when phones, the associated controllers, PC-based 
consoles, and the LAN infrastructure need to continue to operate during a power failure. UPSs 
can range from simple local battery units to larger central installations that include backup 
generators. Consider the following factors to determine the type of unit to use:

•

The power to be drawn by attached units

•

The power output of the UPS, and its efficiency with battery capability

•

The time the UPS must supply power

•

The size of the unit.

Worked Example

Consider a small installation with a LAN switch and some powered phones. The LAN switch 
draws 100 W and 16 attached phones draw 8 W each. The UPS has a 12 V battery of 55 AH 
and runs at 70% efficiency. How long can this combination be powered?

•

The output power available is 462 VAH (volt-amperes hour) (55 x 12 x 70%).

•

The consumption is 228 VA (100 W + 16 x 8 W).

•

The time available is 2 hours or 462 VAH / 228 VA.

America Power Conversion (APC) is a company that designs and sells UPS systems. Some 
useful calculations can also be found at the APC web site:

http://www.apc.com/tools/ups_selector/index.cfm

Mitel products are listed under “VoIP Solutions.” (Although information appeared correct when 
this publication was written, Mitel cannot take responsibility for incorrect information entered 
or supplied from this tool.)

Notes: 

1.

If VoIP service must be operational during a power failure, each of the network 

components must also be on the UPS.

2.

The System Engineering Tool will estimate the amount of power used by each of 

the cabinets in the system configuration when running the existing traffic. The 
estimate does not include the power for other network equipment (L2 switches, and 
so forth).

Note:

 Volt-Amperes (VA) is equivalent to Watts (W) if the Power Factor Correction 

(PFC) of the power supply in question has a PFC value of close to 1. Most data 
switches on the market today will have a PFC value close to 1.

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

HTC TOUCH DUAL - Smartphone - WCDMA Quick Start Manual preview
TOUCH DUAL - Smartphone - WCDMA
Brand: HTC Pages: 2
Sagem myC5-2m Technical Documentation Manual preview
myC5-2m
Brand: Sagem Pages: 115
iBall Vogue 2.8a SLEEC User Manual preview
Vogue 2.8a SLEEC
Brand: iBall Pages: 23
HTC U12+ Manual preview
U12+
Brand: HTC Pages: 4
Samsung SGH T319 Manual Del Usuario preview
SGH T319
Brand: Samsung Pages: 182
Samsung SGHP735 User Manual preview
SGHP735
Brand: Samsung Pages: 193
Samsung SGH T349 Information Manual preview
SGH T349
Brand: Samsung Pages: 2
Samsung SM-A057G Repair Manual preview
SM-A057G
Brand: Samsung Pages: 126
Samsung SM-A107F/DS User Manual preview
SM-A107F/DS
Brand: Samsung Pages: 119
Acer P400 User Manual preview
P400
Brand: Acer Pages: 91
Acer P300 User Manual preview
P300
Brand: Acer Pages: 96
Acer V370 User Manual preview
V370
Brand: Acer Pages: 51
Acer Liquid Z330 User Manual preview
Liquid Z330
Brand: Acer Pages: 77
Acer Liquid Z2 Service Manual preview
Liquid Z2
Brand: Acer Pages: 52
Acer Liquid Z630S Quick Manual preview
Liquid Z630S
Brand: Acer Pages: 32
Acer Liquid Z4 User Manual preview
Liquid Z4
Brand: Acer Pages: 60
Acer M900 User Manual preview
M900
Brand: Acer Pages: 119
Acer liquid z205 User Manual preview
liquid z205
Brand: Acer Pages: 75

Brands by name

Popular brands

Load more brands