Mitel MiVOICE BUSINESS Engineering Manualline Download Page 126 | Manualshive

Page: 126 / 381

background image

Engineering Guidelines

112

POWER REQUIREMENTS FOR 5220 IP PHONE OPTIONAL
ACCESSORIES

The 5220 IP Phone and the 5220 IP Phone (Dual Mode) support optional accessories which
are powered in different ways depending on the option and the phone:

•

5220 IP Phone options are powered from a 24 VDC power unit only.

•

5220 IP Phone (Dual Mode) options can be powered from either 24 VDC power unit or
through the Ethernet.

An alternate way of identifying whether a phone is dual mode or not is by the “Top Engineering
Number” which can be found on a label on the back of the phone.

Table 37: Top Engineering Number by Phone

SYSTEM POWER REQUIREMENTS

ICP power requirements are detailed in the

3300 ICP Hardware Technical Reference Manual

.

This document is available via Mitel On Line.

CAUTION: The 5550 IP Console and the 5310 IP Conference Unit can only be
powered with AC adapters that provide a 24 VDC output. To prevent damage do
not use PoE or an In-Line Ethernet AC Power Adapter to power either of them.

Note:

To determine whether your phone is a 5220 IP Phone or 5220 IP Phone (Dual

Mode), check the label on the back of the set. 5220 IP Phone (Dual Mode) sets are
identified as either “5220 Dual Port” or “5220 Dual Mode”.

MODEL OF PHONE

TOP ENGINEERING NUMBER (T.E.N. #)

5215

56004354

5220

56004352 & 56005271

5215 Dual Mode

56005585

5220 Dual Mode

56005587

Note:

During a local power failure, data being written to a disk or FLASH module may

not be completely stored and therefore could become corrupted. Use of RAID can
improve the integrity and data validation, but cannot guarantee data that wasn't
completely transferred due to loss of power. Systems most affected would be those
undergoing updates, or those that store voice mail. We strongly recommend that these
systems, including the ICPs, be powered through UPS units or similar power backup
systems. More details on platform power consumption and settings can be found in the

3300 ICP Hardware Technical Reference Manual

.

«
...
124
125
126
127
128
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: Haier Pages: 42

Brand: UCall Pages: 54

Brand: Yamaha Pages: 14

Brand: Yamaha Pages: 28

Brand: Yamaha Pages: 109

Brand: Yamaha Pages: 3

IX Room Systems XT4 00 Series

Brand: Avaya Pages: 90

Brand: UTStarcom Pages: 55

Brand: DMP Electronics Pages: 4

Brand: DIS Pages: 2

Brand: Plum Pages: 24

Brand: Verykool Pages: 30

2 VOICE 1083/58

Brand: urmet domus Pages: 60

Meridian Norstar

Brand: Nortel Pages: 18

Brand: snopfon Pages: 46

Brand: Zte Pages: 26

Brand: Zte Pages: 79

Brand: Paso Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands