Mitel MiVOICE BUSINESS Engineering Manualline Download Page 117 | Manualshive

Page: 117 / 381

background image

Power

103

REMOTE POWER

As mentioned earlier in this document, there are three communication standards that phones
can use to advertise their power requirements to an Ethernet switch that supports a PoE
mechanism. In all cases, both the phone and the powered Ethernet switch must comply with
the same standard. The three standards are:

•

Cisco Discovery Protocol (CDP)

•

IEEE 802.3af Power Over Ethernet Standard (PoE)

•

IEEE 802.3ab Link layer Discovery Protocol (LLDP-MED).

Gigabit Ethernet Phone Stand Version 1. Note: This power is for the
stand only, the phone power is not included.

5.3

Gigabit Ethernet Phone Stand Version 2. Note: This power is for the
stand only, the phone power is not included.

3.4

Wireless LAN Phone Stand
Note: This power is for the stand only; the phone power is not
included.

5.3

Cordless OM / Handset plus headset (for 5330/5330 with backlight/
5340) (see Note 2)

3.0

5560 IPT

12.9

Bluetooth Module for use with 5330, 5340 and 5360.

3.0

UC360

The UC360 can consume up to 25.5
Watts, however typical power
consumption is less. For details refer to
the UC360 Engineering Guidelines.

Note 1

: See “Power Restrictions” on page 68. for information about power restrictions related to the Gigabit

Ethernet Phone Stand.

Note 2

: The power consumed by this device adds to the power consumption of the phone it is

attached to.

Note 3

: The Programmable Key Modules (PKM) are available in two different models, the 5412 and the 5448.

In situations where the PKMs are powered via PoE the installer must add the PKM power consumption and the
phone power consumption together to determine the total power consumption.

Note 4

: The 5360 will draw 9.2 Watts when it is in Gigabit Ethernet mode and 7.9 Watts when in 10/100 Mb/s

mode.

Note:

The CXi and CXi II only support the IEEE 802.3af PoE standard.

Table 33: Actual Telephone Power Consumption (continued)

DEVICE

POWER CONSUMPTION (W)

(WORST CASE MAXIMUM)

Page 3 of 3

«
...
115
116
117
118
119
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: Indicom Pages: 37

Brand: Iget Pages: 63

Brand: Ericsson Pages: 37

Brand: OUKITEL Pages: 59

Brand: Audiovox Pages: 49

Brand: Samsung Pages: 128

SGH-T259 Series

Brand: Samsung Pages: 155

SGH-T229 Series

Brand: Samsung Pages: 140

SGH-T109 Series

Brand: Samsung Pages: 128

SGH-T159 Series

Brand: Samsung Pages: 173

Brand: Samsung Pages: 217

Brand: Samsung Pages: 92

Brand: Samsung Pages: 120

Brand: Creator Electronics Pages: 53

Brand: Hitachi Pages: 44

Brand: Hitachi Pages: 52

Brand: Hitachi Pages: 95

Brand: Hitachi Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands